| 数据搜索系统,热门电子元器件搜索 |
|
ADM1266ACPZ-R7 数据表(PDF) 25 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADM1266ACPZ-R7 数据表(HTML) 25 Page - Analog Devices |
|
25 / 62 page ![]() Data Sheet ADM1266 Rev. A | Page 25 of 62 PASSWORD PROTECTION Specific commands are password protected to avoid unintended modification of the firmware, sequence, and project configuration data in the ADM1266. These commands must be unlocked only when updating the firmware, sequence, and project configuration data. Table 9 shows the list of password protected commands. It is not required to unlock the device for regular operation. The password is 16 bytes, and for the default password, those 16 bytes are all 0xFF. Table 9. Password Protected Commands Command Address UPDATE_FW 0xFC SEQUENCE_CONFIGURATION 0xD6 SYSTEM_CONFIGURATION 0xD7 LOGIC_CONFIGURATION 0xE0 USER_DATA 0xE3 STORE_USER_ALL 0x15 REFRESH_FLASH 0xF5 ERASE_MEMORY 0xFB MEMORY_CONFIGURATION 0xF8 UNLOCKING THE DEVICE The ADM1266 can be unlocked by performing two consecutives writes of the correct password to the FW_PASSWORD command (Register 0xFD). The block write command for unlocking the device is shown in Figure 16. The unlock status can be confirmed by the PART_LOCKED bit of the STATUS_MFR_SPECFIC command (Register 0x80) which is set to 0 when the device is successfully unlocked. LOCKING THE DEVICE Upon a power cycle, the device is automatically locked. The device can also be locked by writing any 17 bytes of data once to the FW_PASSWORD command (Register 0xFD). The block write command for locking the device is shown in Figure 17. The lock status can be confirmed by the PART_LOCKED bit of the STATUS_MFR_SPECFIC (Register 0x80) command, which is set to 1 when the device is successfully locked. CHANGING THE PASSWORD The password can be changed by the user to any 16-byte value. For password less than 16 bytes, set the remaining bytes as 0x00. To update the password, the device must be unlocked by following the procedure described in the Unlocking the Device section. After the device is unlocked, the new password must be written two consecutive times to the FW_PASSWORD command (Register 0xFD). The block write command for changing the password is shown in Figure 18. After the password is updated, the new password is immediately committed to the memory. The device is automatically locked and must be unlocked using the new password. S 7-BIT SLAVE ADDRESS BYTE COUNT = 17 W A A A 0xFD A A ... = MASTER-TO-SLAVE = SLAVE-TO-MASTER A P PASSWORD BYTE 1 PASSWORD BYTE 16 PASSWORD COMMAND = 2 Figure 16. Block Write Command for Unlocking the Device S 7-BIT SLAVE ADDRESS BYTE COUNT = 17 W A A A 0xFD A A ... = MASTER-TO-SLAVE = SLAVE-TO-MASTER A P PASSWORD BYTE 1 PASSWORD BYTE 16 PASSWORD COMMAND = 3 Figure 17. Block Write Command for Locking the Device S 7-BIT SLAVE ADDRESS BYTE COUNT = 17 W A A A 0xFD A A ... = MASTER-TO-SLAVE = SLAVE-TO-MASTER A P NEW PASSWORD BYTE 1 PASSWORD COMMAND = 1 NEW PASSWORD BYTE 16 Figure 18. Block Write Command for Changing the Password |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |