ADAV803ASTZ datasheet(18/56 Pages) AD

18 / 56 page

ADAV803

Rev. 0 | Page 18 of 56

pair

28 steps

ded to remove high

e noise

nal

op amps, which might draw mor than 50 µA or have dynamic

load changes, extra buffering should be used to preserve the

qua

an be selected from

.375

ault to

electing a Sample Rate

Correct operation of the DAC is dependent upon the data rate

provided to the DAC, the master clock applied to the DAC, and

the selected interpolation rate. By default, the DAC assumes that

the MCLK rate is 256 times the sample rate, which requires an

8-times oversampling rate. This combination is suitable for

sample rates of up to 48 kHz.

For a 96 kHz data rate that has a 24.576 MHz MCLK (256 × fS)

associated with it, the DAC MCLK divider should be set to

divide the MCLK by 2. This prevents the DAC engine from

running too fast. To compensate for the reduced MCLK rate, the

interpolator should be selected to operate in 4 × (DAC MCLK =

128 × fS). Similar combinations can be selected for different

sample rates.

REG 0x63

BITS 5–3

DAC SECTION

The ADAV803 has two DAC channels arranged as a stereo

with single-ended analog outputs. Each channel has its own

independently programmable attenuator, adjustable in 1

of 0.375 dB per step. The DAC can receive data from the

playback or auxiliary input ports, the SRC, the ADC, or the DIR.

Each analog output pin sits at a dc level of VREF, and swings 1.0

V rms for a 0 dB digital input signal. A single op amp third-

order external low-pass filter is recommen

frequency noise present on the output pins. Note that the use of

op amps with low slew rate or low bandwidth can cause high

frequency noise and tones to fold down into the audio band.

Care should be taken in selecting these components.

The FILTD and FILTR pins should be bypassed by external

capacitors to AGND. The FILTD pin is used to reduce th

of the internal DAC bias circuitry, thereby reducing the DAC

output noise. The voltage at the VREF pin, FILTR, can be use

to bias external op amps used to filter the output signals. For

applications in which the FILTR is required to drive exter

lity of the ADAV803 reference.

The digital input data source for the DAC c

a number of available sources by programming the appropriate

bits in the datapath control register. Figure 27 shows how the

digital data source and the MCLK source for the DAC are

selected. Each DAC has an independent volume register giving

256 steps of control, with each step giving approximately 0

dB of attenuation. Note that the DACs are muted by def

prevent unwanted pops, clicks, and other noises from appearing

on the outputs while the ADAV803 is being configured. Each

DAC also has a peak-level register that records the peak value of

the digital audio data. Reading the register clears the peak.

REG 0x76

BITS 7–5

REG 0x65

BITS 3–2

DIR

PLAYBACK

AUXILIARY IN

ADC

MCLK

DIVIDER

DAC

MCLK

DAC

INPUT

Figure 27. Clock and Datapath Control on the DAC

MULTI-BIT

Σ-∆

MODULATOR

INTERPOLATOR

DAC

TO ZERO FLAG PINS

FROM DAC

DATA PATH

MULTIPLEXER

VOLUME/MUTE

CONTROL

PEAK

DETECTOR

ZERO DETECT

TO CONTROL

REGISTERS

ANALOG

OUTPUT

Figure 28. DAC Block Diagram

ADAV803ASTZ 数据表(PDF) 18 Page - Analog Devices

ADAV803ASTZ 数据表(HTML) 18 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表下载