 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
ADIN1110CCPZ-R7 数据表(PDF) 102 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADIN1110CCPZ-R7 数据表(HTML) 102 Page - Analog Devices |
|
|
102 / 104 page  Data Sheet ADIN1110 REGISTERS analog.com Rev. 0 | 102 of 104 Table 214. Bit Descriptions for FG_DONE Bits Bit Name Description Reset Access 0 FG_DONE Frame Generator Done. This bit reads as 1 to indicate that the generation of frames has completed. When set, this bit goes high and it latches high until its unlatched by reading. 0x0 R LH MAC Interface Loopbacks Configuration Register Device Address: 0x1F; Register Address: 0x8055, Reset: 0x000A, Name: MAC_IF_LOOPBACK MAC interface loopbacks configuration. Table 215. Bit Descriptions for MAC_IF_LOOPBACK Bits Bit Name Description Reset Access [15:4] RESERVED Reserved. 0x0 R 3 MAC_IF_REM_LB_RX_SUP_EN Suppress RX Enable. Suppress receiver to the MAC when MAC_IF_REM_LB_EN is set. 0x1 R/W 2 MAC_IF_REM_LB_EN MAC Interface Remote Loopback Enable. Receive data is looped back to the transmitter. 0x0 R/W 1 MAC_IF_LB_TX_SUP_EN Suppress Transmission Enable. Suppress transmission to the PHY when MAC_IF_LB_EN is set. 0x1 R/W 0 MAC_IF_LB_EN MAC Interface Loopback Enable. Transmit data is looped back to the receiver. 0x0 R/W MAC Start of Packet (SOP) Generation Control Register Device Address: 0x1F; Register Address: 0x805A, Reset: 0x001B, Name: MAC_IF_SOP_CNTRL Table 216. Bit Descriptions for MAC_IF_SOP_CNTRL Bits Bit Name Description Reset Access [15:6] RESERVED Reserved. 0x0 R 5 MAC_IF_TX_SOP_LEN_CHK_EN Enable TX SOP Preamble Length Check. 0x0 R/W 4 MAC_IF_TX_SOP_SFD_EN Enable TX SOP Signal Indication on start of frame delimiter (SFD). 0x1 R/W 3 MAC_IF_TX_SOP_DET_EN Enable the Generation of the TX SOP Indication Signal. 0x1 R/W 2 MAC_IF_RX_SOP_LEN_CHK_EN Enable RX SOP Preamble Length Check. If this bit is set and no SFD is received, the RX SOP signal indication is set after eight bytes. Otherwise, the RX SOP is not set if no SFD is received in the first eight bytes. 0x0 R/W 1 MAC_IF_RX_SOP_SFD_EN Enable RX SOP Signal Indication on SFD Reception. If both MAC_IF_RX_SOP_DET_EN and MAC_IF_RX_SOP_SFD_EN are set, the RX SOP signal is set when the SFD is received. Otherwise, the RX SOP is set when RX_DV is set. The RX SOP signal remains set until the end of the frame. 0x1 R/W 0 MAC_IF_RX_SOP_DET_EN Enable the Generation of the RX SOP Indication Signal. 0x1 R/W |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
