ADIN1100CCPZ-R7 datasheet(19/80 Pages) AD

19 / 80 page

Data Sheet

ADIN1100

THEORY OF OPERATION

analog.com

Rev. B | 19 of 80

Following a hardware interrupt on the INT pin, the interrupt

source can be checked with the CRSM_SW_IRQ_LH bit in

CRSM_IRQ_STATUS (see the System Interrupt Status Register

section).

System Error Interrupts

The ADIN1100 can also generate system errors interrupts. The

interrupt flags are located within the reserved bit sections of

CRSM_IRQ_STATUS (see the System Interrupt Status Register

section).

CRSM_IRQ_MASK (see the System Interrupt Mask Register sec-

tion) must be configured to allow system error interrupts. Refer

to Table 94 for details on the interrupts mask. The ADIN1100

must be hardware reset to recover from a system error interrupt

(CRSM_IRQ_STATUS reserved bits read as 1).

RESET OPERATIONS

Overview

The ADIN1100 supports the following chip resets:

►

Power-on reset

►

Hardware reset

►

Software reset

►

MAC interface reset

►

PHY subsystem reset

All of these resets put the ADIN1100, including the PHY core, into a

known state. Whenever the PHY core is reset, the ADIN1100 MAC

interface output pins are driven to a low state.

Power-On Reset

The ADIN1100 includes a power supply monitoring circuit to ensure

that the chip has the correct voltage supply before initiating the

power-up sequence. During power-up, the ADIN1100 is held in

hardware reset until each of the supplies has crossed its minimum

rising threshold value and the power is considered good.

Hardware Reset

A hardware reset is initiated by the power-on reset circuitry or

by asserting the RESET pin low for a minimum of 10 µs. The

ADIN1100 includes a deglitch circuitry on this pin to reject pulses

shorter than 1 µs.

When the RESET pin is deasserted, all the input/output (I/O) pins

are held in tristate mode, the hardware configuration pins are

latched, and the I/O pins are configured to their functional mode.

When all the external and internal supplies are valid and stable,

the crystal oscillator circuit is enabled. After the crystal has started

up and stabilized, the phase-locked loop (PLL) is enabled. After a

delay of 50 ms (maximum) from the deassertion of the RESET pin,

all the internal clocks are valid, the internal logic is released from

reset, and all the management interface registers are accessible

over the MDIO interface.

The CLK25_REF clock output stays low while the RESET pin is

asserted low and remains low for another 70 ms (maximum) after

the RESET pin is deasserted.

Software Reset

A full chip software reset is initiated by setting the software reset

bit (CRSM_SFT_RST). When this bit is set, the chip fully initializes,

almost equivalent to a hardware reset except that it does not go

through the voltage supply validation sequence. The I/O pins are

held in tristate mode, the hardware configuration pins are latched,

and then the I/O pins are configured to their functional mode.

The crystal oscillator circuit is enabled, and after the crystal has

started up and stabilized, the PLL is enabled. Approximately 10 ms

(maximum) after setting the CRSM_SFT_RST bit, the internal logic

is released from reset and all the management interface registers

are accessible. The system ready bit (CRSM_SYS_RDY) indicates

that the start-up sequence is complete and the system is ready for

normal operation.

The CLK25_REF clock output remains low for 25 ms (maximum)

following a software reset.

PHY Subsystem Reset

A PHY subsystem reset is initiated on the ADIN1100 by setting the

PHY subsystem reset register bit (CRSM_PHY_SUBSYS_RST) to

1. The reset is applied for typically 1.2 µs, and then this bit self

clears. All of the PHY digital circuitry is reset, and any available ac-

tive link drops. The PHY subsystem reset does not alter the values

of the management registers, which remain accessible throughout

the sequence. The subsystem reset is a short reset and can be

used to put the device into a known state while retaining the internal

MAC Interface Reset

A MAC interface reset is initiated on the ADIN1100 by setting the

PHY MAC interface reset register bit (CRSM_MAC_IF_RST) to 1.

The reset is applied for typically 1.2 µs, and then this bit self clears.

A reset sequence is provided to the ADIN1100 MAC interface,

but without dropping the available active link. This reset interrupts

any packet transmission or reception on the MAC interface, but

does not drop an existing active link nor prevent a link from being

established. The MAC interface reset does not alter the values of

the management registers, which remain accessible throughout the

sequence.

ADIN1100CCPZ-R7 数据表(PDF) 19 Page - Analog Devices

ADIN1100CCPZ-R7 数据表(HTML) 19 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表下载