| 数据搜索系统,热门电子元器件搜索 |
|
MPC8313VRGDDB 数据表(PDF) 44 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
MPC8313VRGDDB 数据表(HTML) 44 Page - Freescale Semiconductor, Inc |
|
44 / 100 page ![]() MPC8313E PowerQUICC™ II Pro Processor Hardware Specifications, Rev. 2.1 44 Freescale Semiconductor High-Speed Serial Interfaces (HSSI) Figure 31. Differential Measurement Points for Rise and Fall Time Figure 32. Single-Ended Measurement Points for Rise and Fall Time Matching The other detailed AC requirements of the SerDes reference clocks is defined by each interface protocol based on application usage. Refer to the following section for detailed information: • Section 8.3.2, “AC Requirements for SGMII SD_REF_CLK and SD_REF_CLK 9.2.4.1 Spread Spectrum Clock SD_REF_CLK/SD_REF_CLK are not intended to be used with, and should not be clocked by, a spread spectrum clock source. Rising edge rate (SDn_REF_CLK) to falling edge rate (SDn_REF_CLK) matching Rise-fall matching —20 % 1, 4 Notes: 1. Measurement taken from single-ended waveform. 2. Measurement taken from differential waveform. 3. Measured from –200 to +200 mV on the differential waveform (derived from SD n_REF_CLK minus SDn_REF_CLK). The signal must be monotonic through the measurement region for rise and fall time. The 400 mV measurement window is centered on the differential zero crossing. See Figure 31. 4. Matching applies to rising edge rate for SD n_REF_CLK and falling edge rate for SDn_REF_CLK. It is measured using a 200 mV window centered on the median cross point, where SD n_REF_CLK rising meets SDn_REF_CLK falling. The median cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. The rise edge rate of SD n_REF_CLK should be compared to the fall edge rate of SDn_REF_CLK, the maximum allowed difference should not exceed 20% of the slowest edge rate. See Figure 32. Table 40. SerDes Reference Clock Common AC Parameters (continued) At recommended operating conditions with XVDD_SRDS1 or XVDD_SRDS2 = 1.0 V ± 5%. Parameter Symbol Min Max Unit Notes VIH = +200 mV VIL = –200 mV 0.0 V SD n_REF_CLK Minus SD n_REF_CLK Fall Edge Rate Rise Edge Rage SD n_REF_CLK SD n_REF_CLK SD n_REF_CLK SD n_REF_CLK SD n_REF_CLK VCROSS MEDIAN VCROSS MEDIAN VCROSS MEDIAN + 100 mV VCROSS MEDIAN – 100 mV TFALL TRISE |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |