ATtiny13A datasheet(60/174 Pages) ATMEL

60 / 174 page

8126D–AVR–11/09

ATtiny13A

11.2.1

Registers

The Timer/Counter (TCNT0) and Output Compare Registers (OCR0A and OCR0B) are 8-bit

registers. Interrupt request (abbreviated to Int.Req. in the figure) signals are all visible in the

Timer Interrupt Flag Register (TIFR0). All interrupts are individually masked with the Timer Inter-

rupt Mask Register (TIMSK0). TIFR0 and TIMSK0 are not shown in the figure.

The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on

the T0 pin. The Clock Select logic block controls which clock source and edge the Timer/Counter

uses to increment (or decrement) its value. The Timer/Counter is inactive when no clock source

is selected. The output from the Clock Select logic is referred to as the timer clock (clkT0).

The double buffered Output Compare Registers (OCR0A and OCR0B) is compared with the

Timer/Counter value at all times. The result of the compare can be used by the Waveform Gen-

erator to generate a PWM or variable frequency output on the Output Compare pins (OC0A and

OC0B). See “Output Compare Unit” on page 61. for details. The Compare Match event will also

set the Compare Flag (OCF0A or OCF0B) which can be used to generate an Output Compare

interrupt request.

11.2.2

Definitions

Many register and bit references in this section are written in general form. A lower case “n”

replaces the Timer/Counter number, in this case 0. A lower case “x” replaces the Output Com-

pare Unit, in this case Compare Unit A or Compare Unit B. However, when using the register or

bit defines in a program, the precise form must be used, i.e., TCNT0 for accessing

Timer/Counter0 counter value and so on.

The definitions in Table 11-1 on page 60 are also used extensively throughout the document.

11.3 Timer/Counter Clock Sources

The Timer/Counter can be clocked by an internal or an external clock source. The clock source

is selected by the Clock Select logic which is controlled by the Clock Select (CS02:0) bits

located in the Timer/Counter Control Register (TCCR0B). For details on clock sources and pres-

caler, see “Timer/Counter Prescaler” on page 77.

11.4 Counter Unit

The main part of the 8-bit Timer/Counter is the programmable bi-directional counter unit. Figure

11-2 shows a block diagram of the counter and its surroundings.

Table 11-1.

Definitions

BOTTOM

The counter reaches the BOTTOM when it becomes 0x00.

MAX

The counter reaches its MAXimum when it becomes 0xFF (decimal 255).

TOP

The counter reaches the TOP when it becomes equal to the highest value in the

count sequence. The TOP value can be assigned to be the fixed value 0xFF

(MAX) or the value stored in the OCR0A Register. The assignment is depen-

dent on the mode of operation.

ATtiny13A 数据表(PDF) 60 Page - ATMEL Corporation

ATtiny13A 数据表(HTML) 60 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载