ATtiny13A datasheet(61/174 Pages) ATMEL

61 / 174 page

8126D–AVR–11/09

ATtiny13A

Figure 11-2. Counter Unit Block Diagram

Signal description (internal signals):

count

Increment or decrement TCNT0 by 1.

direction

Select between increment and decrement.

clear

Clear TCNT0 (set all bits to zero).

clkTn

Timer/Counter clock, referred to as clkT0 in the following.

top

Signalize that TCNT0 has reached maximum value.

bottom

Signalize that TCNT0 has reached minimum value (zero).

Depending of the mode of operation used, the counter is cleared, incremented, or decremented

at each timer clock (clkT0). clkT0 can be generated from an external or internal clock source,

selected by the Clock Select bits (CS02:0). When no clock source is selected (CS02:0 = 0) the

timer is stopped. However, the TCNT0 value can be accessed by the CPU, regardless of

whether clkT0 is present or not. A CPU write overrides (has priority over) all counter clear or

count operations.

The counting sequence is determined by the setting of the WGM01 and WGM00 bits located in

the Timer/Counter Control Register (TCCR0A) and the WGM02 bit located in the Timer/Counter

Control Register B (TCCR0B). There are close connections between how the counter behaves

(counts) and how waveforms are generated on the Output Compare output OC0A. For more

details about advanced counting sequences and waveform generation, see “Modes of Opera-

tion” on page 64.

The Timer/Counter Overflow Flag (TOV0) is set according to the mode of operation selected by

the WGM01:0 bits. TOV0 can be used for generating a CPU interrupt.

11.5 Output Compare Unit

The 8-bit comparator continuously compares TCNT0 with the Output Compare Registers

(OCR0A and OCR0B). Whenever TCNT0 equals OCR0A or OCR0B, the comparator signals a

match. A match will set the Output Compare Flag (OCF0A or OCF0B) at the next timer clock

cycle. If the corresponding interrupt is enabled, the Output Compare Flag generates an Output

Compare interrupt. The Output Compare Flag is automatically cleared when the interrupt is exe-

cuted. Alternatively, the flag can be cleared by software by writing a logical one to its I/O bit

location. The Waveform Generator uses the match signal to generate an output according to

operating mode set by the WGM02:0 bits and Compare Output mode (COM0x1:0) bits. The max

and bottom signals are used by the Waveform Generator for handling the special cases of the

extreme values in some modes of operation (See “Modes of Operation” on page 64.).

Figure 11-3 on page 62 shows a block diagram of the Output Compare unit.

DATA BUS

TCNTn

Control Logic

count

TOVn

(Int.Req.)

Clock Select

top

Edge

Detector

( From Prescaler )

clk

bottom

direction

clear

ATtiny13A 数据表(PDF) 61 Page - ATMEL Corporation

ATtiny13A 数据表(HTML) 61 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载