 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
WM8904ECS/R 数据表(PDF) 160 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8904ECS/R 数据表(HTML) 160 Page - Wolfson Microelectronics plc |
|
|
160 / 188 page  WM8904 Pre-Production w PP, Rev 3.3, September 2012 160 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION REFER TO R61 (3Dh) Analogue OUT12 ZC 3 HPL_BYP_EN A 0 Selects input for left headphone output MUX 0 = Left DAC 1 = Left input PGA (Analogue bypass) Output Signal Paths Enable 2 HPR_BYP_EN A 0 Selects input for right headphone output MUX 0 = Right DAC 1 = Right input PGA (Analogue bypass) Output Signal Paths Enable 1 LINEOUTL_BY P_ENA 0 Selects input for left line output MUX 0 = Left DAC 1 = Left input PGA (Analogue bypass) Output Signal Paths Enable 0 LINEOUTR_BY P_ENA 0 Selects input for right line output MUX 0 = Right DAC 1 = Right input PGA (Analogue bypass) Output Signal Paths Enable Register 3Dh Analogue OUT12 ZC REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION REFER TO R67 (43h) DC Servo 0 3 DCS_ENA_CH AN_3 0 DC Servo enable for LINEOUTR 0 = disabled 1 = enabled DC Servo 2 DCS_ENA_CH AN_2 0 DC Servo enable for LINEOUTL 0 = disabled 1 = enabled DC Servo 1 DCS_ENA_CH AN_1 0 DC Servo enable for HPOUTR 0 = disabled 1 = enabled DC Servo 0 DCS_ENA_CH AN_0 0 DC Servo enable for HPOUTL 0 = disabled 1 = enabled DC Servo Register 43h DC Servo 0 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION REFER TO R68 (44h) DC Servo 1 15 DCS_TRIG_SI NGLE_3 0 Writing 1 to this bit selects a single DC offset correction for LINEOUTR. In readback, a value of 1 indicates that the DC Servo single correction is in progress. DC Servo 14 DCS_TRIG_SI NGLE_2 0 Writing 1 to this bit selects a single DC offset correction for LINEOUTL. In readback, a value of 1 indicates that the DC Servo single correction is in progress. DC Servo 13 DCS_TRIG_SI NGLE_1 0 Writing 1 to this bit selects a single DC offset correction for HPOUTR. In readback, a value of 1 indicates that the DC Servo single correction is in progress. DC Servo 12 DCS_TRIG_SI NGLE_0 0 Writing 1 to this bit selects a single DC offset correction for HPOUTL. In readback, a value of 1 indicates that the DC Servo single correction is in progress. DC Servo 11 DCS_TRIG_SE RIES_3 0 Writing 1 to this bit selects a series of DC offset corrections for LINEOUTR. In readback, a value of 1 indicates that the DC Servo DAC Write correction is in progress. DC Servo |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
