MMPF0200Z datasheet(87/118 Pages) NXP

87 / 118 page

Analog Integrated Circuit Device Data



Freescale Semiconductor

PF0200Z

Functional Block Requirements and Behaviors

Power Generation

6.4.7.1

Coin Cell Battery Backup

The LICELL pin provides for a connection of a coin cell backup battery or a “super” capacitor. If the voltage at VIN goes below

the VIN threshold (VTL1 and VTL0), contact-bounced, or removed, the coin cell maintained logic will be powered by the voltage

applied to LICELL. The supply for internal logic and the VSNVS rail will switch over to the LICELL pin when VIN goes below VTL1

or VTL0, even in the absence of a voltage at the LICELL pin, resulting in clearing of memory and turning off of VSNVS. When

system operation below VTL1 is required, for systems not utilizing a coin cell, connect the LICELL pin to any system voltage

between 1.8 and 3.0 V. A small capacitor should be placed from LICELL to ground under all circumstances.

Coin Cell Charger Control

The coin cell charger circuit will function as a current-limited voltage source, resulting in the CC/CV taper characteristic typically

used for rechargeable Lithium-Ion batteries. The coin cell charger is enabled via the COINCHEN bit while the coin cell voltage is

programmable through the VCOIN[2:0] bits on register COINCTL on Table 97. The coin cell charger voltage is programmable.

In the ON state, the charger current is fixed at ICOINHI. In Sleep and Standby modes, the charger current is reduced to a typical

A. In the OFF state, coin cell charging is not available as the main battery could be depleted unnecessarily. The coin cell

charging will be stopped when VIN is below UVDET.

External Components

Table 96. Coin Cell Charger Voltage

VCOIN[2:0]

VCOIN (V)(67)

000

2.50

001

2.70

010

2.80

011

2.90

100

3.00

101

3.10

110

3.20

111

3.30

Notes

67.

Coin cell voltages selected based on the

type of LICELL used on the system.

Table 97. Register COINCTL - ADDR 0x1A

Name

Bit #

R/W

Default

Description

VCOIN

2:0

R/W

0x00

Coin cell charger output voltage selection.

See Table 96 for all options selectable through

these bits.

COINCHEN

R/W

0x00

Enable or disable the Coin cell charger

UNUSED

7:4

–

0x00

UNUSED

Table 98. Coin Cell Charger External Components

Component

Value

Units

LICELL Bypass Capacitor

100

MMPF0200Z 数据表(PDF) 87 Page - NXP Semiconductors

MMPF0200Z 数据表(HTML) 87 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

MMPF0200Z 数据表(PDF) 87 Page - NXP Semiconductors

MMPF0200Z 数据表(HTML) 87 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载