| 数据搜索系统,热门电子元器件搜索 |
|
MCP2518FD 数据表(PDF) 51 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP2518FD 数据表(HTML) 51 Page - Microchip Technology |
|
51 / 96 page ![]() 2019 Microchip Technology Inc. DS20006027A-page 51 MCP2518FD REGISTER 3-27: CiTXQSTA – TRANSMIT QUEUE STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 31 bit 24 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 23 bit 16 U-0 U-0 U-0 R-0 R-0 R-0 R-0 R-0 — — —TXQCI<4:0>( 1) bit 15 bit 8 HS/C-0 HS/C-0 HS/C-0 HS/C-0 U-0 R-1 U-0 R-1 TXABT( 2)( 3) TXLARB ( 2)( 3) TXERR( 2)( 3) TXATIF — TXQEIF —TXQNIF bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 3-13 Unimplemented: Read as ‘0’ bit 12-8 TXQCI<4:0>: Transmit Queue Message Index bits( 1) A read of this register will return an index to the message that the FIFO will next attempt to transmit. bit 7 TXABT: Message Aborted Status bit( 2)( 3) 1 = Message was aborted 0 = Message completed successfully bit 6 TXLARB: Message Lost Arbitration Status bit( 2)( 3) 1 = Message lost arbitration while being sent 0 = Message did not loose arbitration while being sent bit 5 TXERR: Error Detected During Transmission bit( 2)( 3) 1 = A bus error occurred while the message was being sent 0 = A bus error did not occur while the message was being sent bit 4 TXATIF: Transmit Attempts Exhausted Interrupt Pending bit 1 = Interrupt pending 0 = Interrupt Not pending bit 3 Unimplemented: Read as ‘0’ bit 2 TXQEIF: Transmit Queue Empty Interrupt Flag bit 1 = TXQ is empty 0 = TXQ is not empty, at least 1 message queued to be transmitted bit 1 Unimplemented: Read as ‘0’ bit 0 TXQNIF: Transmit Queue Not Full Interrupt Flag bit 1 = TXQ is not full 0 = TXQ is full Note 1: TXQCI<4:0> gives a zero-indexed value to the message in the TXQ. If the TXQ is 4 messages deep (FSIZE = 5’h03) TXQCI will take on a value of 0 to 3 depending on the state of the TXQ. 2: This bit is cleared when TXREQ is set or by writing a 0 using the SPI. 3: This bit is updated when a message completes (or aborts) or when the TXQ is reset. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |