R31DS0210EU0106 Rev.1.06

Page 16

May 11, 2026

RC193xx Datasheet

Table 10. PCIe Refclk Phase Jitter (CLKSEL_tri = 0 or 1, Both CLKIN Running at Different Frequencies) – Degraded

Conditions [1][2][3][4]

1. The Refclk jitter is measured after applying the filter functions found in the PCI Express Base Specification 7.0. For the exact measurement setup,

see Test Loads. The worst case results for each data rate are summarized in this table. Equipment noise is removed from all measurements.

2. Jitter measurements are made with a capture of at least 100,000 clock cycles captured by a real-time oscilloscope (RTO) with a sample rate of

20GS/s or greater. Broadband oscilloscope noise must be minimized in the measurement. The measured PP jitter is used (no extrapolation) for

RTO measurements. Alternately, jitter measurements can be made with a Phase Noise Analyzer (PNA) extending (flat) and integrating and folding

the frequency content up to an offset from the carrier frequency of at least 200MHz (at 300MHz absolute frequency) below the Nyquist frequency.

For PNA measurements for the 2.5GT/s data rate, the RMS jitter is converted to peak-to-peak jitter using a multiplication factor of 8.83.

3. Differential input swing ≥ 800mV and input slew rate ≥ 1.5V/ns. The rms sum of the source jitter and the additive jitter (arithmetic sum for PCIe

Gen1) must be less than the jitter specification listed.

4. One input clock at 100MHz, the other input clock at 99.75MHz, 100MHz clock measured.

Symbol

Parameter

Condition

Typical

Maximum

Spec. Limit

Unit

tjphPCIeG1-CC

Additive PCIe Phase Jitter

(Common Clocked Architecture)

PCIe Gen1 (2.5 GT/s)

3230

5491

86,000

fs p-p

tjphPCIeG2-CC

PCIe Gen2 Hi Band (5.0 GT/s)

159

343

3,100

fs

RMS

PCIe Gen2 Lo Band (5.0 GT/s)

345

546

3,000

tjphPCIeG3-CC

PCIe Gen3 (8.0 GT/s)

86

131

1,000

tjphPCIeG4-CC

PCIe Gen4 (16.0 GT/s) [5][6]

5. SSC spurs from the fundamental and harmonics are removed up to a cutoff frequency of 2MHz taking care to minimize removal of any non-SSC

content.

6. Note that 0.7ps RMS is to be used in channel simulations to account for additional noise in a real system.

86

131

500

tjphPCIeG5-CC

PCIe Gen5 (32.0 GT/s) [4][7]

7. Note that 0.25ps RMS is to be used in channel simulations to account for additional noise in a real system.

24

39

150

tjphPCIeG6-CC

PCIe Gen6 (64.0 GT/s) [4][8]

8. Note that 0.15ps RMS is to be used in channel simulations to account for additional noise in a real system.

19

28

100

tjphPCIeG7-CC

PCIe Gen7 (128 GT/s) [4][9]

9. Note that 0.10ps RMS is to be used in channel simulations to account for additional noise in a real system.

13

20

67

tjphPCIeG2-IR

Additive PCIe Phase Jitter

(IR Architectures)

PCIe Gen2 (5.0 GT/s)

390

594

[10]

10. The PCI Express Base Specification 7.0 provides the filters necessary to calculate SRIS jitter values; it does not provide specification limits,

therefore, the reference to this footnote in the Limit column. SRIS values are informative only. A common practice is to split the common clock

budget in half. For 16GT/s data rates and above, the user must choose whether to use the output jitter specification, or the input jitter specification,

which includes an allocation for the jitter added by the channel. Using 32GT/s, the Refclk jitter budget is 150fs RMS. One half of the Refclk jitter

budget is 106fs RMS. At the clock input, the system must deliver 250fs RMS. One half of this value is 177fs RMS. If the clock is placed next to the

PCIe device in an SRIS system, the channel is very short and the user can choose to use this more relaxed value as the jitter limit.

fs

RMS

tjphPCIeG3-IR

PCIe Gen3 (8.0 GT/s)

123

190

tjphPCIeG4-IR

PCIe Gen4 (16.0 GT/s) [3][4]

131

202

tjphPCIeG5-IR

PCIe Gen5 (32.0 GT/s) [3][5]

28

46

tjphPCIeG6-IR

PCIe Gen6 (64.0 GT/s) [3][7]

26

39

tjphPCIeG7-IR

PCIe Gen7 (128 GT/s) [3][7]

18

28