 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
WM8904ECS/R 数据表(PDF) 173 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8904ECS/R 数据表(HTML) 173 Page - Wolfson Microelectronics plc |
|
|
173 / 188 page  Pre-Production WM8904 w PP, Rev 3.3, September 2012 173 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION REFER TO R126 (7Eh) Digital Pulls 7 MCLK_PU 0 MCLK pull-up resistor enable 0 = pull-up disabled 1 = pull-up enabled Digital Audio Interface Control 6 MCLK_PD 0 MCLK pull-down resistor enable 0 = pull-down disabled 1 = pull-down enabled Digital Audio Interface Control 5 DACDAT_PU 0 DACDAT pull-up resistor enable 0 = pull-up disabled 1 = pull-up enabled Digital Audio Interface Control 4 DACDAT_PD 0 DACDAT pull-down resistor enable 0 = pull-down disabled 1 = pull-down enabled Digital Audio Interface Control 3 LRCLK_PU 0 LRCLK pull-up resistor enable 0 = pull-up disabled 1 = pull-up enabled Digital Audio Interface Control 2 LRCLK_PD 0 LRCLK pull-down resistor enable 0 = pull-down disabled 1 = pull-down enabled Digital Audio Interface Control 1 BCLK_PU 0 BCLK pull-up resistor enable 0 = pull-up disabled 1 = pull-up enabled Digital Audio Interface Control 0 BCLK_PD 0 BCLK pull-down resistor enable 0 = pull-down disabled 1 = pull-down enabled Digital Audio Interface Control Register 7Eh Digital Pulls REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION REFER TO R127 (7Fh) Interrupt Status 10 IRQ 0 Logical OR of all other interrupt flags Interrupts 9 GPIO_BCLK_EI NT 0 GPIO4 interrupt 0 = interrupt not set 1 = interrupt is set Cleared when a ‘1’ is written Interrupts 8 WSEQ_EINT 0 Write Sequence interrupt 0 = interrupt not set 1 = interrupt is set Cleared when a ‘1’ is written. Note that the read value of WSEQ_EINT is not valid whilst the Write Sequencer is Busy Interrupts 7 GPIO3_EINT 0 GPIO3 interrupt 0 = interrupt not set 1 = interrupt is set Cleared when a ‘1’ is written Interrupts 6 GPIO2_EINT 0 GPIO2 interrupt 0 = interrupt not set 1 = interrupt is set Cleared when a ‘1’ is written Interrupts 5 GPIO1_EINT 0 GPIO1 interrupt 0 = interrupt not set 1 = interrupt is set Cleared when a ‘1’ is written Interrupts |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
