3UG3501 datasheet(14/114 Pages) ETC2

14 / 114 page

SIMOCODE 3UF Motor Management and Control Devices

SIMOCODE pro 3UF7

motor management and control devices

7/14

Siemens LV 1 T · 2006

■Technical specifications

General data applicable to the basic units, current measuring

modules, current/voltage measuring modules, expansion modules

and operator panel

Permissible ambient temperature

• During operation

°C

-25 ... +60

• Storage and transport

°C

-40 ... +80

Installation altitude above sea level

2000

• Permissible ambient temperature max. +50 °C

(no safe isolation)

3000

• Permissible ambient temperature max. +40 °C

(no safe isolation)

4000

Degree of protection (acc. to IEC 60529)

• All components

(except for current measuring modules or current/voltage measuring

modules for busbar connection, operator panel and door adapter)

IP20

• Current measuring modules or current/voltage measuring module with

busbar connection

IP00

• Operator panel (front) and door adapter (front) with cover

IP54

Shock resistance (sine pulse)

g/ms

15/11

Mounting position

Any

Frequency

50/60

Immunity to electromagnetic interferences (acc. to IEC 60947-1)

Corresponds to degree of severity 3

• Line-induced interference, burst acc. to IEC 61000-4-4

2 (power ports)

1 (signal port)

• Conducted interference, high frequency acc. to IEC 61000-4-6

• Line-induced interference, surge acc. to IEC 61000-4-5

2 (line to ground)

1 (line to line)

• Electrostatic discharge, ESD acc. to IEC 61000-4-2

8 (air discharge)

6 (contact discharge)

• Field-related interference acc. to IEC 61000-4-3

V/m

Immunity to electromagnetic interferences (acc. to IEC 60947-1)

• Line-conducted and radiated interference emission

EN 55011 / EN 55022 (CISPR 11 / CISPR 22)

(corresponds to degree of severity A)

Safe isolation (acc. to IEC 60947-1)

All circuits in SIMOCODE pro are safely isolated from each other acc. to

IEC 60947-1, they are designed with doubled creepage paths and

clearances

In this context, compliance with the instructions in the test report "Safe

Isolation" No. 2668 is required.

Basic units

Mounting

Snap-on mounting onto 35 mm standard mounting rail or

screw fixing with additional push-in lugs

Displays

• Red/green "DEVICE" LED

Green: "Ready"

Red: "Function test not OK; device is disabled"

Off:

"No control supply voltage"

• Green "BUS" LED

Continuous light: "Communication with PLC/PCS"

Flashing:

"Baud rate recognized/communicating with PC/PG"

• Red "GEN. FAULT" LED

Continuous light/flashing: "Feeder fault", e.g. Overload tripping

Test/Reset buttons

• Resets the device after tripping

• Function test

• Operation of a memory module or addressing plug

System interfaces

•Front

Connection of an operator panel or expansion modules; the memory

module, addressing plug or a PC cable can also be connected to the system

interface for parameterizing

•Bottom

Connection of a current measuring module or current/voltage measuring

module

PROFIBUS DP interface

Connection of the PROFIBUS DP cable over terminals or

over a 9-pin sub D female connector

3UG3501 数据表(PDF) 14 Page - List of Unclassifed Manufacturers

3UG3501 数据表(HTML) 14 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载