HMC1197LP7FE datasheet(20/57 Pages) AD

20 / 57 page

For price, delivery, and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824

Phone: 978-250-3343

Fax: 978-250-3373

Order On-line at www.hittite.com

Application Support: Phone: 978-250-3343 or apps@hittite.com

HMC1197LP7FE

v03.0314

Wideband direct Quadrature Modulator

w/ Fractional-n Pll & Vco, 100 - 4000 MHz

Suppose the HMC1197LP7FE output frequency is to operate at 2.01 GHz. Our example crystal frequency

is fxtal = 50 MHz, R=1, and m=0 (Figure 37), hence TFSM = 20 ns (50 MHz). Note, when using AutoCal, the

maximum AutoCal Finite State Machine (FSM) clock cannot exceed 50 MHz (see Reg 0Ah[14:13]). The

FSM clock does not affect the accuracy of the measurement, it only affects the time to produce the result.

This same clock is used to clock the 16 bit VCO serial port.

If time to change frequencies is not a concern, then one may set the calibration time for maximum accuracy,

and therefore not be concerned with measurement resolution.

Using an input crystal of 50 MHz (R=1 and fpd=50 MHz) the times and accuracies for calibration using

(EQ 6) and (EQ 8) are shown in Table 10 Where minimal tuning time is 1/8th of the VCO band spacing.

Across all VCOs, a measurement resolution better than 800 kHz will produce correct results. Setting

m = 0, n = 5, provides 781 kHz of resolution and adds 8.6 µs of AutoCal time to a normal frequency hop.

Once the AutoCal sets the final switch value, 8.64 µs after the frequency change command, the fractional

as shown in this example that AutoCal typically adds about 8.6 µs to the normal time to achieve frequency

lock. Hence, AutoCal should be used for all but the most extreme frequency hopping requirements.

table 10. autocal example with F

xtal = 50 MHz, r = 1, m = 0

Control Value

Reg0Ah[2:0]

Tmmt

(µs)

Tcal

(µs)

Ferr Max

0.02

4.92

± 25 MHz

0.04

5.04

± 12.5 MHz

0.08

5.28

± 6.25 MHz

0.16

5.76

± 3.125 MHz

0.64

8.64

± 781 kHz

1.28

12.48

± 390 kHz

128

2.56

20.16

± 195 kHz

256

5.12

35.52

± 98 kHz

1.2.1.5 Manual Vco calibration for Fast Frequency Hopping

If it is desirable to switch frequencies quickly it is possible to eliminate the AutoCal time by calibrating

the VCO in advance and storing the switch number vs frequency information in the host. This can be

done by initially locking the HMC1197LP7FE on each desired frequency using AutoCal, then reading,

and storing the selected VCO switch settings. The VCO switch settings are available inReg 15h[8:1] after

every AutoCal operation. The host must then program the VCO switch settings directly when changing

frequencies. Manual writes to the VCO switches are executed immediately as are writes to the integer and

fractional registers when AutoCal is disabled. Hence frequency changes with manual control and AutoCal

disabled, requires a minimum of two serial port transfers to the HMC1197LP7FE, once to set the VCO

switches, and once to set the PLL frequency.

If AutoCal is disabled Reg 0Ah[11]=1, the VCO will update its registers with the value written via Reg

15h[8:1] immediately.

1.2.2

registers required for Frequency changes in Fractional Mode

A large change of frequency, in fractional mode (Reg 06h[11]=1), may require Main Serial Port writes to:

1. The integer register intg, Reg 03h (only required if the integer part changes)

2. Manual VCO Tuning Reg 15h only required for manual control of VCO if Reg 0Ah[11]=1 (AutoCal

disabled)

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registered trademarks are the property of their respective owners.

For price, delivery, and to place orders: Analog Devices, Inc.,

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106

Phone: 781-329-4700 • Order online at www.analog.com

Application Support: Phone: 1-800-ANALOG-D

HMC1197LP7FE 数据表(PDF) 20 Page - Analog Devices

HMC1197LP7FE 数据表(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

数据表下载