TNETX15AE datasheet(64/78 Pages) TI

64 / 78 page

TNETX15AE

ADDRESS-LOOKUP DEVICE

SPWS041A – AUGUST 1997 – REVISED OCTOBER 1997

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

absolute maximum ratings over operating case temperature range (unless otherwise noted)†

Supply voltage range, VCC (see Notes 2 and 3)

–0.5 V to 3.6 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Supply voltage range, VCC(5V) (see Notes 2 and 3)

–0.5 V to 5.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input voltage range, VI

–0.5 V to VCC(5 V) + 0.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output voltage range, VO

–0.5 V to VCC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Thermal impedance, junction-to-ambient package, airflow = 0, ZθJA

47.5

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . .

Thermal impedance, junction-to-ambient package, airflow = 100 ft/min, ZθJA

38.2

°C/W

. . . . . . . . . . . . . . . . .

Thermal impedance, junction-to-case package, ZθJC

9.9

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating case temperature range, TC

°C to 95°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range, Tstg

–65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” can cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods can affect device reliability.

NOTES:

2. All voltage values are with respect to GND.

3. Turning power supplies on and off (cycling sequence) within a mixed 5-V/3.3-V system is an important consideration. The designer

must observe a few rules to avoid damaging the TNETX15AE. Check with the manufacturers of all components used in the 3.3-V

to 5-V interface to ensure that no unique device characteristics exist that would lead to rules more restrictive than the TNETX15AE

requires.

The optimum solution to power-supply sequencing in a mixed-voltage system is to ramp up the 3.3-V supply first. A power-on reset

component operating from this supply forces all 5-V tolerant outputs into the high-impedance state. Then, the 5-V supply is ramped

up. On power down, the 5-V rail deenergizes first, followed by the 3.3-V rail.

The second-best solution is to ramp both the 3.3-V and 5-V rails at the same time, making sure that no more than 3.6 V exists between

these two rails during the ramp up or down. If the 3.3 V is derived from the 5 V, then the 3.3 V rises as the 5 V rises so that the 5-V

rail never exceeds the 3.3-V rail by more than 3.6 V. Both the optimum and second-choice algorithms for power up prevent any device

damage. If it is impractical to implement ramping, follow these rules:

• When turning on the power supply, all 3.3-V and 5-V supplies should start ramping from 0 V and reach 95 percent of their end-point

values within 25 ms. All bus contention between the device and external devices is eliminated by the end of 25 ms.

• When turning off the power supply, 3.5-V and 5-V supplies should start ramping from steady-state values and reach 5 percent

of these values within 25 ms. All bus contention between the device and external devices is eliminated by the end of 25 ms. There

is a 250-second lifetime maximum at greater than 3.6 V between the supply rails. Holding this period to 25 ms per power-on/off

cycle should not significantly contribute to shifts in mean time between failures (MTBF) during product lifetimes.

recommended operating conditions

MIN

NOM

MAX

UNIT

VCC

Supply voltage

3.3

3.6

VCC(5V)

Supply voltage

4.5

5.5

VIH

High-level input voltage

VCC(5V)

VIL

Low-level input voltage (see Note 4)

0.8

IOH

High-level output current

–4

IOL

Low-level output current

NOTE 4: The algebraic convention, where the more-negative (less-positive) limit is designated as a minimum, is used for logic-voltage levels only.

TNETX15AE 数据表(PDF) 64 Page - Texas Instruments

TNETX15AE 数据表(HTML) 64 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

数据表下载

链接网址

TNETX15AE 数据表(PDF) 64 Page - Texas Instruments

TNETX15AE 数据表(HTML) 64 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

数据表 下载

链接网址

数据表下载