GLS53 datasheet(70/109 Pages) EMERSON-NETWORKPOWER

70 / 109 page

GLS53-I Installation & Operating Instructions

P/N: A272-207 Rev 0 6/29/09 Ref: 03370201560

While every precaution has been taken to ensure accuracy and completeness in this manual, EGS Electrical Group, LLC.

assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions

GLS53-I is a commercial designation of model number LPS53(-I).

To comply with the published safety standards, the following must be observed when using

this power supply:

1. Maximum ambient temperature for the power supply must not exceed 50°C. The power

supply has been evaluated for use in 70°C at half load and 80°C at quarter load.

2. When installing the power supply in the end-use equipment, special attention is

required to ensure safety compliance with the following safety standards: UL60950-1,

EN60950-1, IEC60950-1, and CSA22.2 No. 60950-1-03. The safety requirements

include creepage distances, clearances, and distance through insulation between

primary wiring and earth or secondary (SELV) wiring.

3. This power supply is approved and certified for the rated voltage range of 100 V ac to

240 V ac.

4. The maximum output power of the supply must not exceed the rating indicated in the

specification sheet.

5. The disconnection from the line must be in the end system.

6. The unit must be protected with dc rated fuse when operating in a dc input voltage.

7. The internal fuse should only be replaced with a 3.15A, 250 V ac, type TE5/392 manufac-

tured by Wickmann.

8. This equipment is considered Class I according to protection against electric shock.

9. This power supply is

marked following the provisions of the Low Voltage Directive,

2006/95/EC.

10. For technical assistance, contact SolaHD Technical Support at (800) 377-4384 or send

an e-mail to tech@solahd.com. Please visit our Web site at www.solahd.com for addi-

tional product information and specification sheets.

Output Ratings

Output Voltage (V)

Convection Cooling

Max. Output Current (A)

Max. Output Power (W)

+12

5.0

Connector PIN Designation

Input Connector

Designation

SK1

Line

Neutral

Output Connector

Designation

SK2

+12 V

Common

-Sense

+Sense

Mechanical Outline & Dimensions

Mounting Hole

.16 [4.0] 4 X

3.73

[94.7]

4.00

[101.6]

.16

[4.0]

Earth

GND

Output Voltage

Adjust Pot

SK1

SK2

Top View

Side View

All dimensions are in inches [mm].

Maximum screw head diameter is .22″ [5.6 mm].

Mounting holes M1 and M2 should be grounded for EMI

purposes. Mounting hole M1 is an earth ground connection.

CAUTION! Do not accidentally connect the ac connector to

the dc output.

GLS53 数据表(PDF) 70 Page - Emerson Network Power

GLS53 数据表(HTML) 70 Page - Emerson Network Power

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载