GLS53 datasheet(76/109 Pages) EMERSON-NETWORKPOWER

76 / 109 page

GLS58, GLS58-M Installation & Operating Instructions

GLS58/58-M are commercial designations of model numbers LPS58/58-M respectively.

P/N: A272-185 Rev 0 4/28/09 Ref: LPS58/OP

To comply with the published safety standards, the following must be observed when using this

power supply:

1. Maximum ambient temperature for the power supply must not exceed 50°C. The power

supply has been evaluated for use in 70°C at half load (30 W) for GLS58 only.

2. When installing the power supply in the end-use equipment, special attention is required

to ensure safety compliance with the following safety standards: UL60950-1, EN60950-1,

IEC60950-1, and CSA22.2 No. 60950-1-03 for GLS58; UL60601-1, EN60601-1,

IEC60601-1, and CSA22.2 No. 60601-1-M90 for GLS58-M. The safety requirements include

creepage distances, clearances, and distance through insulation between primary wiring and

earth or secondary (SELV) wiring.

3. This power supply is approved and certified for the rated voltage range of 100 V ac to 240 V ac.

4. The maximum output power of the supply must not exceed the rating indicated in the specifi-

cation sheet.

5. The disconnection from the line must be in the end system.

6. The internal fuse should only be replaced with a T3.15AH, 250 V ac, type TE5/392 manufac-

tured by Wickmann.

NOTE: The power supply has a fuse on the neutral line for GLS58-M.

7. GLS58-M has no patient applied part.

8. This equipment is considered Class I according to protection against electric shock.

9. This power supply is

marked following the provisions of the Low Voltage Directive,

2006/95/EC.

10. For technical assistance, contact SolaHD Technical Support at (800) 377-4384 or send an

e-mail to tech@solahd.com. Please visit our Web site at www.solahd.com for additional

product information and specification sheets.

Output Ratings

Output Voltage (V)

Convection Cooling

Max. Output Current (A)

Max. Output Power (W)

+48

1.25

Connector PIN Designation

Input Connector

Designation

SK1

Line

Neutral

Output Connector

Designation

SK2

+48 V

Common

-Sense

+Sense

Mechanical Outline & Dimensions

Mounting Hole

.16 [4.0] 4 X

3.73

[94.7]

4.00

[101.6]

.16

[4.0]

Earth

GND

Output Voltage

Adjust Pot

SK1

SK2

Top View

Side View

All dimensions are in inches [mm].

Maximum screw head diameter is .22″ [5.6 mm].

Mounting holes M1 and M2 should be grounded for EMI

purposes.

Mounting hole M1 is an earth ground connection.

CAUTION! Do not accidentally connect the ac connector

to the dc output.

GLS53 数据表(PDF) 76 Page - Emerson Network Power

GLS53 数据表(HTML) 76 Page - Emerson Network Power

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载