ST25R3916 datasheet(43/157 Pages) STMICROELECTRONICS

43 / 157 page

DS12484 Rev 4

43/157

ST25R3916/7

Application information

156

(5 ms for ISO14443) requiring that the reader field must be turned on for some time before

first command is sent. General purpose timer can be used to count this time or NFC Field

On command with a defined time by the NFC field on guard timer register.

Preparation and execution of a transceive sequence:



Execute the direct command Stop all activities



Execute the direct command Reset RX gain



Configure the timers accordingly



Define the number of transmitted bytes in the Number of transmitted bytes register 1

and Number of transmitted bytes register 2



Write the bytes to be transmitted in the FIFO (not in the case of direct commands

REQA and WUPA)



Send one of the commands Transmit with CRC, Transmit without CRC, Transmit

REQA or Transmit WUPA



When all the data is transmitted an interrupt is sent to inform the microcontroller that

the transmission is finished (IRQ due to end of transmission)

After the transmission is executed, the ST25R3916/7 receiver automatically starts to

observe the RFI inputs to detect a transponder response. The RSSI and AGC (in case it is

enabled) are started. The framing block processes the subcarrier signal from receiver and

fills the FIFO with data. When the reception is finished and all the data is in the FIFO an

interrupt is sent to the microcontroller (IRQ due to end of receive), and the FIFO status

microcontroller can proceed with data download.

If an error or bit collision is detected during reception, an interrupt with appropriate flag is

sent, and the microcontroller must take appropriate action.

When data packets longer than FIFO have to be transmitted the sequence detailed above

changes.

The FIFO is prepared with data before the transmission starts. An interrupt is sent during the

transmission to signal when the remaining number of bytes is lower than the water level

(IRQ due to FIFO water level). The microcontroller then adds more data in the FIFO. When

all the data are transmitted an interrupt is sent to inform the microcontroller that the

transmission is finished.

The situation during reception time is similar. When the FIFO is loaded with more data than

the receive water level, an interrupt is sent and the microcontroller reads the data from the

FIFO. When the reception is finished an interrupt is sent to the microcontroller (IRQ due to

end of receive) the FIFO status register 1 and FIFO status register 1 display the number of

bytes in the FIFO still to be read.

4.2.14

Listen mode

The ST25R3916/7 listen/target mode is activated by setting to 1 bit targ in the Mode

definition register. There are various target or listening modes implemented depending on

setting of the om<3:0> bits, refer to Table 24: Target operation modes.

The main modes are



NFCIP-1 active target



Passive target used for Card mode and NFCIP-1 passive target

ST25R3916 数据表(PDF) 43 Page - STMicroelectronics

ST25R3916 数据表(HTML) 43 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载