CS5501-SD datasheet(17/54 Pages) CIRRUS

17 / 54 page

excellent differential linearity achieved by the

CS5501. The CS5501/CS5503 also have excellent

integral linearity, which is accomplished with a

well-designed charge-balance architecture.

Each

device also achieves low input drift through the

use of chopper-stabilized techniques in its input

stage. To assure that the CS5501/CS5503 achieves

excellent performance over time and temperature,

it uses digital calibration techniques to minimize

offset and gain errors to typically within

±1/2

LSB at 16 bits in the CS5501 and

±4 LSB at 20

bits in the CS5503.

Converter Calibration

The CS5501/CS5503 offer both self-calibration

and system level calibration capability. To under-

stand th e calibratio n features, a basic

comprehension of the internal workings of the

converter are helpful. As mentioned previously in

this data sheet, the converter consists of two sec-

tions.

First is the analog modulator which is a

delta-sigma type charge-balance converter.

This

is followed by a digital filter. The filter circuitry

is actually an arithmetic logic unit (ALU) whose

architecture and instructions execute the filter

function. The modulator (explained in more de-

tail in the applications note "Delta-Sigma

Conversion Technique Overview") uses the VREF

voltage connected to pin 10 to determine the mag-

nitude of the voltages used in its feedback DAC.

The modulator accepts an analog signal at its in-

put and produces a data stream of 1’s and 0’s as

its output.

This data stream value can change

(from 1 to 0 or vice versa) every 256 CLKIN cy-

cles. As the input voltage increases the ratio of

1’s to 0’s out of the modulator increases propor-

tionally. The 1’s density of the data stream out of

the modulator therefore provides a digital repre-

sentation of the analog input signal where the 1’s

density is defined as the ratio of the number of 1’s

to the number of 0’s out of the modulator for a

given period of time. The 1’s density output of the

modulator is also a function of the voltage on the

VREF pin. If the voltage on the VREF pin in-

creases in value (say, due to temperature drift), and

the analog input voltage into the modulator remains

constant, the 1’s density output of the modulator will

decrease (less 1’s will occur). The analog input into

the modulator which is necessary to produce a given

binary output code from the converter is ratiometric

to the voltage on the VREF pin. This means that if

VREF increases by one per cent, the analog signal

on AIN must also increase by one per cent to main-

tain the same binary output code from the converter.

For a complete calibration to occur, the calibration

microcontroller inside the device needs to record

the data stream 1’s density out of the modulator

for two different input conditions. First, a "zero

scale" point must be presented to the modulator.

Then a "full scale" point must be presented to the

modulator.

In unipolar self-cal mode the zero

scale point is AGND and the full scale point is the

voltage on the VREF pin. The calibration micro-

controller then remembers the 1’s density out of

the modulator for each of these points and calcu-

lates a slope factor (LSB/

µV). This slope factor

65,535

Codes

32,768

-1

+1/2

-1/2

Figure 8. CS5501 Differential Nonlinearity Plot

CS5501/CS5503

DS31F2

CS5501-SD 数据表(PDF) 17 Page - Cirrus Logic

CS5501-SD 数据表(HTML) 17 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

数据表下载