PIC16F753 datasheet(60/230 Pages) MICROCHIP

60 / 230 page

PIC16F753/HV753

DS40001709C-page 60

 2013-2015 Microchip Technology Inc.

7.5.2.1

T1G Pin Gate Operation

The T1G pin is one source for Timer1 gate control. It

can be used to supply an external source to the Timer1

gate circuitry.

7.5.2.2

Timer0 Overflow Gate Operation

When Timer0 increments from FFh to 00h, a low-to-

high pulse will automatically be generated and

internally supplied to the Timer1 gate circuitry.

7.5.2.3

C1OUT/C2OUT Gate Operation

The outputs from the Comparator C1 and C2 modules

can be used as gate sources for the Timer1 module.

7.5.3

TIMER1 GATE TOGGLE MODE

When Timer1 Gate Toggle mode is enabled, it is

possible to measure the full-cycle length of a Timer1

gate signal, as opposed to the duration of a single-level

pulse.

The Timer1 gate source is routed through a flip-flop that

changes state on every incrementing edge of the

signal. See Figure 7-4 for timing details.

Timer1 Gate Toggle mode is enabled by setting the

T1GTM bit of the T1GCON register. When the T1GTM

bit is cleared, the flip-flop is cleared and held clear. This

is necessary in order to control which edge is

measured.

7.5.4

TIMER1 GATE SINGLE-PULSE

MODE

When Timer1 Gate Single-Pulse mode is enabled, it is

possible to capture a single-pulse gate event. Timer1

Gate Single-Pulse mode is first enabled by setting the

T1GSPM bit in the T1GCON register. Next, the

T1GGO/DONE bit in the T1GCON register must be set.

The Timer1 will be fully enabled on the next

incrementing edge. On the next trailing edge of the

pulse, the T1GGO/DONE bit will automatically be

cleared. No other gate events will be allowed to

increment Timer1 until the T1GGO/DONE bit is once

again set in software.

Clearing the T1GSPM bit of the T1GCON register will

also clear the T1GGO/DONE bit. See Figure 7-5 for

timing details.

Enabling the Toggle mode and the Single-Pulse mode

simultaneously will permit both sections to work

together. This allows the cycle times on the Timer1 gate

source to be measured. See Figure 7-6 for timing

details.

7.5.5

TIMER1 GATE VALUE STATUS

When Timer1 gate value status is utilized, it is possible

to read the most current level of the gate control value.

The value is stored in the T1GVAL bit in the T1GCON

gate is not enabled (TMR1GE bit is cleared).

7.5.6

TIMER1 GATE EVENT INTERRUPT

When Timer1 gate event interrupt is enabled, it is

possible to generate an interrupt upon the completion

of a gate event. When the falling edge of T1GVAL

occurs, the TMR1GIF flag bit in the PIR1 register will be

set. If the TMR1GIE bit in the PIE1 register is set, then

an interrupt will be recognized.

The TMR1GIF flag bit operates even when the Timer1

gate is not enabled (TMR1GE bit is cleared).

Note:

Enabling Toggle mode at the same time

as changing the gate polarity may result in

indeterminate operation.

PIC16F753 数据表(PDF) 60 Page - Microchip Technology

PIC16F753 数据表(HTML) 60 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载