PIC16F753 datasheet(61/230 Pages) MICROCHIP

61 / 230 page

 2013-2015 Microchip Technology Inc.

DS40001709C-page 61

PIC16F753/HV753

7.6

Timer1 Interrupt

The Timer1 register pair (TMR1H:TMR1L) increments

to FFFFh and rolls over to 0000h. When Timer1 rolls

over, the Timer1 interrupt flag bit of the PIR1 register is

set. To enable the interrupt on rollover, you must set

these bits:

• TMR1ON bit of the T1CON register

• TMR1IE bit of the PIE1 register

• PEIE bit of the INTCON register

• GIE bit of the INTCON register

The interrupt is cleared by clearing the TMR1IF bit in

the Interrupt Service Routine.

7.7

Timer1 Operation During Sleep

Timer1 can only operate during Sleep when set up in

Asynchronous Counter mode or with the internal

watchdog clock source. In this mode, the clock source

can be used to increment the counter. To set up the

timer to wake the device:

• TMR1ON bit of the T1CON register must be set

• TMR1IE bit of the PIE1 register must be set

• PEIE bit of the INTCON register must be set

• T1SYNC bit of the T1CON register must be set

• TMR1CS bits of the T1CON register must be

configured

• TMR1GE bit of the T1GCON register must be

configured

The device will wake-up on an overflow and execute

the next instructions. If the GIE bit of the INTCON

Routine (0004h).

7.8

CCP Capture/Compare Time Base

The CCP module uses the TMR1H:TMR1L register

pair as the time base when operating in Capture or

Compare mode.

In Capture mode, the value in the TMR1H:TMR1L

In Compare mode, an event is triggered when the value

CCPR1H:CCPR1L register pair matches the value in

the TMR1H:TMR1L register pair. This event can be a

Special Event Trigger.

For more information, see Section 10.0 “Capture/

Compare/PWM Modules”.

7.9

CCP Special Event Trigger

When the CCP is configured to trigger a special event,

the trigger will clear the TMR1H:TMR1L register pair.

This special event does not cause a Timer1 interrupt.

The CCP module may still be configured to generate a

CCP interrupt.

In this mode of operation, the CCPR1H:CCPR1L

Timer1 should be synchronized to the FOSC/4 to utilize

the Special Event Trigger. Asynchronous operation of

Timer1 can cause a Special Event Trigger to be

missed.

In the event that a write to TMR1H or TMR1L coincides

with a Special Event Trigger from the CCP, the write will

take precedence.

For more information, see Section 12.2.5 “Special

Event Trigger”.

FIGURE 7-2:

TIMER1 INCREMENTING EDGE

Note:

The TMR1H:TMR1L register pair and the

TMR1IF bit should be cleared before

enabling interrupts.

T1CKI

TMR1 enabled

Note 1:

Arrows indicate counter increments.

In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge of the clock.

PIC16F753 数据表(PDF) 61 Page - Microchip Technology

PIC16F753 数据表(HTML) 61 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载