XIO2000AI datasheet(61/159 Pages) TAOS

61 / 159 page

Classic PCI Configuration Space

April 2007 Revised October 2008

SCPS155C

4.3

Command Register

The command register controls how the bridge behaves on the PCI Express interface. See Table 4−2 for a

complete description of the register contents.

PCI register offset:

04h

Read-only, Read/Write

Default value:

0000h

BIT NUMBER

RESET STATE

Table 4−2. Command Register Description

BIT

FIELD NAME

ACCESS

DESCRIPTION

15:11

RSVD

Reserved. Returns 00000b when read.

INT_DISABLE

INTx disable. This bit enables device specific interrupts. Since the bridge does not generate any

internal interrupts, this bit is read-only 0b.

FBB_ENB

Fast back-to-back enable. The bridge does not generate fast back-to-back transactions;

therefore, this bit returns 0b when read.

SERR_ENB

SERR enable bit. When this bit is set, the bridge can signal fatal and nonfatal errors on the PCI

Express interface on behalf of SERR assertions detected on the PCI bus.

0 = Disable the reporting of nonfatal errors and fatal errors (default)

1 = Enable the reporting of nonfatal errors and fatal errors

STEP_ENB

Address/data stepping control. The bridge does not support address/data stepping, and this bit is

hardwired to 0b.

PERR_ENB

Controls the setting of bit 8 (DATAPAR) in the status register (offset 06h, see Section 4.4) in

response to a received poisoned TLP from PCI Express. A received poisoned TLP is forwarded

with bad parity to conventional PCI regardless of the setting of this bit.

0 = Disables the setting of the master data parity error bit (default)

1 = Enables the setting of the master data parity error bit

VGA_ENB

VGA palette snoop enable. The bridge does not support VGA palette snooping; therefore, this bit

returns 0b when read.

MWI_ENB

Memory write and invalidate enable. When this bit is set, the bridge translates PCI Express

memory write requests into memory write and invalidate transactions on the PCI interface.

0 = Disable the promotion to memory write and invalidate (default)

1 = Enable the promotion to memory write and invalidate

SPECIAL

Special cycle enable. The bridge does not respond to special cycle transactions; therefore, this

bit returns 0b when read.

MASTER_ENB

Bus master enable. When this bit is set, the bridge is enabled to initiate transactions on the PCI

Express interface.

0 = PCI Express interface cannot initiate transactions. The bridge must disable the response

to memory and I/O transactions on the PCI interface (default).

1 = PCI Express interface can initiate transactions. The bridge can forward memory and I/O

transactions from PCI secondary interface to the PCI Express interface.

MEMORY_ENB

Memory space enable. Setting this bit enables the bridge to respond to memory transactions on

the PCI Express interface.

0 = PCI Express receiver cannot process downstream memory transactions and must

respond with an unsupported request (default)

1 = PCI Express receiver can process downstream memory transactions. The bridge can

forward memory transactions to the PCI interface.

IO_ENB

I/O space enable. Setting this bit enables the bridge to respond to I/O transactions on the PCI

Express interface.

0 = PCI Express receiver cannot process downstream I/O transactions and must respond

with an unsupported request (default)

1 = PCI Express receiver can process downstream I/O transactions. The bridge can forward

I/O transactions to the PCI interface.

XIO2000AI 数据表(PDF) 61 Page - TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS

XIO2000AI 数据表(HTML) 61 Page - TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载