AD9739-R2-EBZ datasheet(47/48 Pages) AD

47 / 48 page

Data Sheet

AD9739

Rev. B | Page 47 of 48

Table 32. Recommended SPI Initialization with SYNC Controller Enabled

Step

Address (Hex)

Write Value

Comments

0x00

Configure for the 4-wire SPI mode with MSB. Note that Bits[7:5] must be mirrored onto

Bits[2:0] because the MSB/LSB format can be unknown at power-up.

0x00

0x20

Software reset to default SPI values.

0x00

Clear the reset bit.

0x22

0x0F

0x23

0x0F

Set the common-mode voltage of DACCLK_P and DACCLK_N inputs.

0x24

0x30

0x25

0x80

0x27

0x44

0x28

0x6C

0x29

0xCB

0x26

0x02

Configure the mu controller. Refer to Table 28 for recommended target Mu slope and

phase settings vs. clock rate.

0x26

0x03

Enable the mu controller search and track mode.

Not applicable

Wait for 160 K × 1/fDATA cycles.

0x2A

Read back Register 0x2A and confirm that it is equal to 0x01 to ensure that the DLL loop

is locked. If it is not locked, proceed to Step 10 and repeat. Limit attempts to three

before breaking out of the loop and reporting a mu lock failure.

0x15

0x42

Configure sync controller.

0x10

0x00

Disable sync controller before enabling it.

0x10

0x60 or 0x40

Enable sync controller for loop and IRQ.

0x60 = master mode.

0x40 = slave mode.

0x10

0x70 or 0x50

Enable sync controller:

0x70 = master mode.

0x50 = slave mode.

Not applicable

Wait for 160 K × 1/fDATA for DLL to lock.

0x21

Read back Register 0x21 to confirm proper operation:

0x90 = master mode.

0x00 = slave mode.

If not, proceed to Step 15 and repeat. Limit to three attempts before breaking out of

loop and reporting sync lock failure.

0x0D

Read back Register 0x0D and confirm Bits[5:4] = 10. If not, proceed to Step 2 and repeat.

Limit to three attempts before breaking out of loop and reporting sync lock failure.

Not applicable

Ensure that the AD9739 is fed with DCI clock input from the data source.

0x13

0x72

Set FINE_DEL_SKEW to 2.

0x10

0x00

Disable the data Rx controller before enabling it.

0x10

0x02

Enable the data Rx controller for loop and IRQ.

0x10

0x03

Enable the data Rx controller for search and track mode.

Wait for 135 K × 1/fDATA cycles.

0x21

Read back Register 0x21 and confirm that it is equal to 0x09 to ensure that the DLL loop

is locked and tracking. If it is not locked and tracking, proceed to Step 16 and repeat.

Limit attempts to three before breaking out of the loop and reporting an Rx data lock

failure.

Not applicable

Readback DCI_DEL value in Register 0x13 and Register 0x14 for master and. If slave

devices are not within 40 codes of each other, re-specify target DCI_DEL value to be

average between master and readback DCI_DEL value.

0x06, 0x07

0x00, 0x02

Optional: modify the TxDAC IOUTFS setting (the default is 20 mA).

0x08

0x00

Optional: modify the TxDAC operation mode (the default is normal mode).

AD9739-R2-EBZ 数据表(PDF) 47 Page - Analog Devices

AD9739-R2-EBZ 数据表(HTML) 47 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表下载

链接网址

AD9739-R2-EBZ 数据表(PDF) 47 Page - Analog Devices

AD9739-R2-EBZ 数据表(HTML) 47 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表 下载

链接网址

数据表下载