ST7MC1 datasheet(87/308 Pages) STMICROELECTRONICS

87 / 308 page

ST7MC1/ST7MC2

87/308

16-BIT TIMER (Cont’d)

3. In PWM mode the ICAP1 pin can not be used

to perform input capture because it is discon-

nected to the timer. The ICAP2 pin can be used

to perform input capture (ICF2 can be set and

IC2R can be loaded) but the user must take

care that the counter is reset each period and

ICF1 can also generates interrupt if ICIE is set.

4. When the Pulse Width Modulation (PWM) and

One Pulse Mode (OPM) bits are both set, the

PWM mode is the only active one.

10.3.4 Low Power Modes

10.3.5 Interrupts

Note: The 16-bit Timer interrupt events are connected to the same interrupt vector (see Interrupts chap-

ter). These events generate an interrupt if the corresponding Enable Control Bit is set and the interrupt

mask in the CC register is reset (RIM instruction).

10.3.6 Summary of Timer modes

1) See note 4 in Section 10.3.3.5 One Pulse Mode

2) See note 5 in Section 10.3.3.5 One Pulse Mode

3) See note 4 in Section 10.3.3.6 Pulse Width Modulation Mode

Mode

Description

WAIT

No effect on 16-bit Timer.

Timer interrupts cause the Device to exit from WAIT mode.

HALT

16-bit Timer registers are frozen.

In HALT mode, the counter stops counting until Halt mode is exited. Counting resumes from the previous

count when the Device is woken up by an interrupt with “exit from HALT mode” capability or from the counter

reset value when the Device is woken up by a RESET.

If an input capture event occurs on the ICAPi pin, the input capture detection circuitry is armed. Consequent-

ly, when the Device is woken up by an interrupt with “exit from HALT mode” capability, the ICFi bit is set, and

the counter value present when exiting from HALT mode is captured into the ICiR register.

Interrupt Event

Event

Flag

Enable

Control

Bit

Exit

from

Wait

Exit

from

Halt

Input Capture 1 event/Counter reset in PWM mode

ICF1

ICIE

Yes

Input Capture 2 event

ICF2

Yes

Output Compare 1 event (not available in PWM mode)

OCF1

OCIE

Yes

Output Compare 2 event (not available in PWM mode)

OCF2

Yes

Timer Overflow event

TOF

TOIE

Yes

MODES

AVAILABLE RESOURCES

Input Capture 1

Input Capture 2

Output Compare 1 Output Compare 2

Input Capture (1 and/or 2)

Yes

Output Compare (1 and/or 2)

Yes

One Pulse Mode

Not Recommended1)

Partially 2)

PWM Mode

Not Recommended3)

ST7MC1 数据表(PDF) 87 Page - STMicroelectronics

ST7MC1 数据表(HTML) 87 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载