ST7MC1 datasheet(22/308 Pages) STMICROELECTRONICS

22 / 308 page

ST7MC1/ST7MC2

22/308

FLASH PROGRAM MEMORY (Cont’d)

4.4 ICC INTERFACE

ICC (In-Circuit Communication) needs a minimum

of four and up to six pins to be connected to the

programming tool (see Figure 10). These pins are:

– RESET: device reset

–VSS: device power supply ground

– ICCCLK: ICC output serial clock pin

– ICCDATA: ICC input/output serial data pin

– ICCSEL/VPP: programming voltage

– OSC1(or OSCIN): main clock input for exter-

nal source (optional)

–VDD: application board power supply (see Fig-

ure 10, Note 3)

Figure 10. Typical ICC Interface

Notes:

1. If the ICCCLK or ICCDATA pins are only used

as outputs in the application, no signal isolation is

necessary. As soon as the Programming Tool is

plugged to the board, even if an ICC session is not

in progress, the ICCCLK and ICCDATA pins are

not available for the application. If they are used as

inputs by the application, isolation such as a serial

resistor has to implemented in case another de-

vice forces the signal. Refer to the Programming

Tool documentation for recommended resistor val-

ues.

2. During the ICC session, the programming tool

must control the RESET pin. This can lead to con-

flicts between the programming tool and the appli-

cation reset circuit if it drives more than 5mA at

high level (push pull output or pull-up resistor<1K).

A schottky diode can be used to isolate the appli-

cation RESET circuit in this case. When using a

classical RC network with R > 1K or a reset man-

agement IC with open drain output and pull-up

resistor > 1K, no additional components are need-

ed. In all cases the user must ensure that no exter-

nal reset is generated by the application during the

ICC session.

3. The use of Pin 7 of the ICC connector depends

on the Programming Tool architecture. This pin

must be connected when using most ST Program-

ming Tools (it is used to monitor the application

power supply). Please refer to the Programming

Tool manual.

4. Pin 9 has to be connected to the OSC1 or OS-

CIN pin of the ST7 when the clock is not available

in the application or if the selected clock option is

not programmed in the option byte. ST7 devices

with multi-oscillator capability need to have OSC2

grounded in this case.

ICC CONNECTOR

HE10 CONNECTOR TYPE

APPLICATION

POWER SUPPLY

PROGRAMMING TOOL

ICC CONNECTOR

APPLICATION BOARD

ICC Cable

(See Note 3)

10k

Ω

ST7

CL2

CL1

OPTIONAL

See Note 1

See Note 2

APPLICATION

RESET SOURCE

APPLICATION

I/O

(See Note 4)

ST7MC1 数据表(PDF) 22 Page - STMicroelectronics

ST7MC1 数据表(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST7MC1 数据表(PDF) 22 Page - STMicroelectronics

ST7MC1 数据表(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载