RA4M1 datasheet(4/130 Pages) RENESAS

4 / 130 page

R01DS0355EJ0100 Rev.1.00

Page 4 of 130

Oct 8, 2019

RA4M1 Group

1. Overview

Table 1.3

System (1 of 2)

Feature

Functional description

Operating modes

Two operating modes:

 Single-chip mode

 SCI/USB boot mode.

See section 3, Operating Modes in User’s Manual.

Resets

14 resets:

 RES pin reset

 Power-on reset

 VBATT-selected voltage power-on reset

 Independent watchdog timer reset

 Watchdog timer reset

 Voltage monitor 0 reset

 Voltage monitor 1 reset

 Voltage monitor 2 reset

 SRAM parity error reset

 SRAM ECC error reset

 Bus master MPU error reset

 Bus slave MPU error reset

 CPU stack pointer error reset

 Software reset.

See section 5, Resets in User’s Manual.

Low Voltage Detection (LVD)

Low Voltage Detection (LVD) function monitors the voltage level input to the VCC pin, and the

detection level can be selected using a software program. See section 7, Low Voltage

Detection (LVD) in User’s Manual.

Clocks

 Main clock oscillator (MOSC)

 Sub-clock oscillator (SOSC)

 High-speed on-chip oscillator (HOCO)

 Middle-speed on-chip oscillator (MOCO)

 Low-speed on-chip oscillator (LOCO)

 PLL frequency synthesizer

 IWDT-dedicated on-chip oscillator

 Clock out support.

See section 8, Clock Generation Circuit in User’s Manual.

Clock Frequency Accuracy

Measurement Circuit (CAC)

The Clock Frequency Accuracy Measurement Circuit (CAC) counts pulses of the clock to be

measured (measurement target clock) within the time generated by the clock to be used as a

measurement reference (measurement reference clock), and determines the accuracy

depending on whether the number of pulses is within the allowable range.

When measurement is complete or the number of pulses within the time generated by the

measurement reference clock is not within the allowable range, an interrupt request is

generated.

See section 9, Clock Frequency Accuracy Measurement Circuit (CAC) in User’s Manual.

Interrupt Controller Unit (ICU)

The Interrupt Controller Unit (ICU) controls which event signals are linked to the NVIC/DTC

module and DMAC module. The ICU also controls NMI interrupts. See section 13, Interrupt

Controller Unit (ICU) in User’s Manual.

Key Interrupt Function (KINT)

A key interrupt can be generated by setting the Key Return Mode Register (KRM) and inputting

a rising or falling edge to the key interrupt input pins. See section 20, Key Interrupt Function

(KINT) in User’s Manual.

Low power modes

Power consumption can be reduced in multiple ways, such as by setting clock dividers,

stopping modules, selecting power control mode in normal operation, and transitioning to low

power modes. See section 10, Low Power Modes in User’s Manual.

Battery backup function

A battery backup function is provided for partial powering by a battery. The battery powered

area includes RTC, SOSC, LOCO, wakeup control, backup memory, VBATT_R low voltage

detection, and switches between VCC and VBATT.

During normal operation, the battery powered area is powered by the main power supply,

which is the VCC pin. When a VCC voltage drop is detected, the power source is switched to

the dedicated battery backup power pin, the VBATT pin.

When the voltage rises again, the power source is switched from the VBATT pin to the VCC

pin. See section 11, Battery Backup Function in User’s Manual.

The register write protection function protects important registers from being overwritten

because of software errors. See section 12, Register Write Protection in User’s Manual.

RA4M1 数据表(PDF) 4 Page - Renesas Technology Corp

RA4M1 数据表(HTML) 4 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载