PIC16F753 datasheet(165/230 Pages) MICROCHIP

165 / 230 page

 2013-2015 Microchip Technology Inc.

DS40001709C-page 165

PIC16F753/HV753

19.7

Power-Down Mode (Sleep)

The Power-Down mode is entered by executing a

SLEEP

instruction.

If the Watchdog Timer is enabled:

• WDT will be cleared but keeps running

•PD bit in the STATUS register is cleared

•TO bit is set

• Oscillator driver is turned off

• I/O ports maintain the status they had before SLEEP

was executed (driving high, low or high-impedance).

For lowest current consumption in this mode, all I/O pins

should be either at VDD or VSS, with no external circuitry

drawing current from the I/O pin and the comparators,

DAC and FVR should be disabled. I/O pins that are high-

impedance inputs should be pulled high or low externally

to avoid switching currents caused by floating inputs.

The T0CKI input should also be at VDD or VSS for lowest

current consumption. The contribution from on-chip pull-

ups on PORTA should be considered.

The MCLR pin must be at a logic high level.

19.7.1

WAKE-UP FROM SLEEP

The device can wake-up from Sleep through one of the

following events:

External Reset input on MCLR pin.

Watchdog Timer wake-up.

Interrupt from INT pin.

Interrupt-On-Change input change.

Peripheral interrupt.

The first event will cause a device Reset. The other

events are considered a continuation of program

execution. The TO and PD bits in the STATUS register

can be used to determine the cause of device Reset.

The PD bit, which is set on power-up, is cleared when

Sleep is invoked. TO bit is cleared if WDT wake-up

occurred.

The following peripheral interrupts can wake the device

from Sleep:

Timer1 interrupt. Timer1 must be operating as

an asynchronous counter.

CCP Capture mode interrupt.

A/D conversion (when A/D clock source is RC).

Comparator output changes state.

Interrupt-on-change.

External Interrupt from INT pin.

Other peripherals cannot generate interrupts since

during Sleep, no on-chip clocks are present.

When the SLEEP instruction is being executed, the next

instruction (PC + 1) is prefetched. For the device to

wake-up through an interrupt event, the corresponding

interrupt enable bit must be set (enabled). Wake-up is

regardless of the state of the GIE bit. If the GIE bit is

clear (disabled), the device continues execution at the

instruction after the SLEEP instruction. If the GIE bit is

set (enabled), the device executes the instruction after

the SLEEP instruction, then branches to the interrupt

address (0004h). In cases where the execution of the

instruction following SLEEP is not desirable, the user

should have a NOP after the SLEEP instruction.

The WDT is cleared when the device wakes up from

Sleep, regardless of the source of wake-up.

19.7.2

WAKE-UP USING INTERRUPTS

When global interrupts are disabled (GIE cleared) and

any interrupt source has both its interrupt enable bit

and interrupt flag bit set, one of the following will occur:

• If the interrupt occurs before the execution of a

SLEEP

instruction, the SLEEP instruction will

complete as a NOP. Therefore, the WDT and WDT

prescaler and postscaler (if enabled) will not be

cleared, the TO bit will not be set and the PD bit

will not be cleared.

• If the interrupt occurs during or after the

execution of a SLEEP instruction, the device will

Immediately wake-up from Sleep. The SLEEP

instruction is executed. Therefore, the WDT and

WDT prescaler and postscaler (if enabled) will be

cleared, the TO bit will be set and the PD bit will

be cleared.

Even if the flag bits were checked before executing a

SLEEP

instruction, it may be possible for flag bits to

become set before the SLEEP instruction completes. To

determine whether a SLEEP instruction executed, test

the PD bit. If the PD bit is set, the SLEEP instruction

was executed as a NOP.

To ensure that the WDT is cleared, a CLRWDT instruction

should be executed before a SLEEP instruction. See

Figure 19-10 for more details.

Note:

It should be noted that a Reset generated

by a WDT time-out does not drive MCLR

pin low.

Note:

If the global interrupts are disabled (GIE is

cleared) and any interrupt source has both

its interrupt enable bit and the correspond-

ing interrupt flag bits set, the device will

immediately wake-up from Sleep.

PIC16F753 数据表(PDF) 165 Page - Microchip Technology

PIC16F753 数据表(HTML) 165 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

PIC16F753 数据表(PDF) 165 Page - Microchip Technology

PIC16F753 数据表(HTML) 165 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载