MPC8309CVMADFC datasheet(17/81 Pages) NXP

17 / 81 page

MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 3

Freescale Semiconductor

DDR2 SDRAM

MCS output setup with respect to MCK

tDDKHCS

333 MHz

266 MHz

2.4

2.5

—

MCS output hold with respect to MCK

tDDKHCX

333 MHz

266 MHz

2.4

2.5

—

MCK to MDQS Skew

tDDKHMH

–0.6

0.6

MDQ/MDM output setup with respect to MDQS

tDDKHDS,

tDDKLDS

333 MHz

266 MHz

0.8

0.9

—

MDQ/MDM output hold with respect to MDQS

tDDKHDX,

tDDKLDX

333 MHz

266 MHz

900

1100

—

MDQS preamble start

tDDKHMP

0.75 x tMCK

—ns

MDQS epilogue end

tDDKHME

0.4 x tMCK

0.6 x tMCK

Notes:

1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for

inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing

(DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example,

tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs

(A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference

(K) goes low (L) until data outputs (D) are invalid (X) or data output hold time.

2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.

3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MDM/MDQS. For the ADDR/CMD

setup and hold specifications, it is assumed that the Clock Control register is set to adjust the memory clocks by 1/2 applied

cycle.

4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD)

from the rising edge of the MCK(n) clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control

of the DQSS override bits in the TIMING_CFG_2 register. This is typically set to the same delay as the clock adjusts in the

CLK_CNTL register. The timing parameters listed in the table assume that these 2 parameters have been set to the same

adjustment value. See the MPC8309 PowerQUICC II Pro Integrated Communications Processor Family Reference Manual

for a description and understanding of the timing modifications enabled by use of these bits.

5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), or data

mask (MDM). The data strobe should be centered inside of the data eye at the pins of the microprocessor.

6. tDDKHMP follows the symbol conventions described in note 1.

Table 16. DDR2 SDRAM Output AC Timing Specifications (continued)

At recommended operating conditions with GVDD of 1.8V ± 100mV.

Parameter

Symbol1

Min

Max

Unit

Note

MPC8309CVMADFC 数据表(PDF) 17 Page - NXP Semiconductors

MPC8309CVMADFC 数据表(HTML) 17 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

数据表下载

链接网址

MPC8309CVMADFC 数据表(PDF) 17 Page - NXP Semiconductors

MPC8309CVMADFC 数据表(HTML) 17 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

数据表 下载

链接网址

数据表下载