ST10 datasheet(8/58 Pages) STMICROELECTRONICS

8 / 58 page

ST10F163

8/58

PORT1:

P1L.0-P1L.7

P1H.0-P1H.7

59-66

67, 68

71-76

I/O

Two 8-bit bidirectional I/O ports P1L and P1H, bit-wise programmable for input

or output via direction bits. For a pin configured as input, the output driver is put

into high-impedance state. PORT1 is used as the 16-bit address bus (A) in

demultiplexed bus modes and also after switching from a demultiplexed bus

mode to a multiplexed bus mode.

RSTIN

Reset Input with Schmitt-Trigger characteristics. A low level at this pin for a

specified duration while the oscillator is running resets the device. An internal

pullup resistor permits power-on reset using only a capacitor connected to

VSS.

RSTOUT

Internal Reset Indication Output. This pin is set to a low level when the part is

executing either a hardware-, a software- or a watchdog timer reset. RSTOUT

remains low until the EINIT (end of initialization) instruction is executed.

NMI

Non-Maskable Interrupt Input. A high to low transition at this pin causes the

CPU to vector to the NMI trap routine. When the PWRDN (power down) instruc-

tion is executed, the NMI pin must be low in order to force the ST10R65 to go

into power down mode. If NMI is high, when PWRDN is executed, the part will

continue to run in normal mode.

If not used, pin NMI should be pulled high externally.

P6.0-P6.7

82-89

I/O

8-bit bidirectional I/O port, bit-wise programmable for input or output via direc-

tion bits. For a pin configured as input, the output driver is put into high-imped-

ance state. Port 6 outputs can be configured as push/pull or open drain drivers.

The following Port 6 pins have alternate functions:

P6.0

CS0

Chip Select 0 Output

...

P6.4

CS4

Chip Select 4 Output

P6.5

HOLD

External Master Hold Request Input

(Master mode: O, Slave mode: I)

I/O

P6.6

HLDA

Hold Acknowledge Output

P6.7

BREQ

Bus Request Output

P2.8 –P2.15

90 - 97

I/O

Port 2 is an 8-bit bidirectional I/O port. It is bit-wise programmable for input or

output via direction bits. For a pin configured as input, the output driver is put

into high-impedance state. Port 2 outputs can be configured as push/pull or

open drain drivers.

The following Port 2 pins also serve for alternate functions:

P2.8

EX0IN

Fast External Interrupt 0 Input

...

P2.15

EX7IN

Fast External Interrupt 7 Input

VPP

Flash programming voltage. This pin accepts the programming voltage for the

on-chip flash EPROM. In the ST10F163, bit 4of SYSCON register serves as an

enable/disable control for the OWD.

VDD

7, 28, 38,

49, 69,

Digital Supply Voltage:

+ 5 V during normal operation and idle mode.

> 2.5 V during power down mode

VSS

4, 27, 39,

50, 70,

Digital Ground.

Table 1 : Pin definitions and functions (continued)

Symbol

Number(

TQFP )

Input (I)

Output

(O)

Function

ST10 数据表(PDF) 8 Page - STMicroelectronics

ST10 数据表(HTML) 8 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58

数据表下载