| 数据搜索系统,热门电子元器件搜索 |
|
H5GQ1H24AFR-R0C 数据表(PDF) 97 Page - Hynix Semiconductor |
|
|
|||||||||||||||||||||||||||||
H5GQ1H24AFR-R0C 数据表(HTML) 97 Page - Hynix Semiconductor |
|
97 / 173 page ![]() This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any responsability for use of circuits described. No patent licenses are implied. Rev. 1.0 /Nov. 2009 97 H5GQ1H24AFR 5.11. READ and WRITE DATA BUS INVERSION (DBI) The GDDR5 SGRAM Data Bus Inversion (DBIdc) reduces the DC power consumption on data pins, as the number of DQ lines driving a low level can be limited to 4 within a byte. DBIdc is evaluated per byte. There is one DBI# pin per byte: DBI0# is associated with DQ0‐DQ7, DBI1# with DQ8‐DQ15, DBI2# with DQ16‐DQ23 and DBI3# with DQ24‐DQ31. The DBI# pins are bidirectional active Low double data rate (DDR) signals. For Writes, they are sampled by the GDDR5 SGRAM along with the DQ of the same byte. For Reads, they are driven by the GDDR5 SGRAM along with the DQ of the same byte. Once enabled by the corresponding RDBI Mode Register bit, the GDDR5 SGRAM inverts read data and sets DBI# Low, when the number of ’0’ data bits within a byte is greater than 4; otherwise the GDDR5 SGRAM does not invert the read data and sets DBI# High, as shown in Figure 64. Once enabled by the corresponding WDBI Mode Register bit, the GDDR5 SGRAM inverts write data received on the DQ inputs in case DBI# was sampled Low, or leaves the data non‐inverted in case DBI# was sampled High, as shown in Figure 65. Figure 64. Example of Data Bus Inversion Logic for READs Figure 65. Example of Data Bus Inversion Logic for WRITEs The flow diagram in Figure 66 illustrates the DBIdc operation. In any case, the transmitter (the controller for WRITEs, the GDDR5 SGRAM for READs) decides whether to invert or not invert the data conveyed on the DQs. The receiver (the GDDR5 SGRAM for WRITEs, the controller for READs) has to perform the reverse operation based on the level on the DBI# pin. Data input and output timing parameters are only valid with DBI being enabled and a maximum of 4 data lines per byte driven Low. 8 8 from DRAM core DQ from Mode Register: 0 = enabled 1 = disabled DBI# ’0’ count >4 8 8 to DRAM core DBI# DQ from Mode Register: 0 = enabled 1 = disabled |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |