H5GQ1H24AFR-R0C datasheet(5/173 Pages) HYNIX

5 / 173 page

Rev. 1.0/Nov. 2009

H5GQ1H24AFR

FEATURES

•Single ended interface for data, address and command

•Quarter data‐rate differential clock inputs CK/CK# for

ADR/CMD

•Two half data‐rate differential clock inputs WCK/

WCK#, each associated with two data bytes (DQ, DBI#,

EDC)

•Double Data Rate (DDR) data (WCK)

•Single Data Rate (SDR) command (CK)

•Double Data Rate (DDR) addressing (CK)

•16 internal banks

•4 bank groups for tCCDL = 3 tCK

•8n prefetch architecture: 256 bit per array read or write

access

•Burst length: 8 only

• Programmable CAS latency: 5 to 20 tCK

• Programmable WRITE latency: 1 to 7 tCK

•WRITE Data mask function via address bus (single/

double byte mask)

• Data bus inversion (DBI) & address bus inversion

(ABI)

• Input/output PLL on/off mode

• Address training: address input monitoring by DQ

pins

• WCK2CK clock training with phase information by

EDC pins

• Data read and write training via READ FIFO

•READ FIFO pattern preload by LDFF command

•Direct write data load to READ FIFO by WRTR

command

•Consecutive read of READ FIFO by RDTR command

• Read/Write data transmission integrity secured by

cyclic redundancy check (CRC‐8)

• READ/WRITE EDC on/off mode

• Programmable EDC hold pattern for CDR

• Programmable CRC READ latency = 0 to 3 tCK

• Programmable CRC WRITE latency = 7 to 14 tCK

•Low Power modes

•RDQS mode on EDC pin

•Optional on‐chip temperature sensor with read‐out

•Auto & self refresh modes

•Auto precharge option for each burst access

• 32ms, auto refresh (8k cycles)

• Temperature sensor controlled self refresh rate

•On‐die termination (ODT); nominal values of 60 ohm

and 120 ohm

•Pseudo open drain (POD‐15) compatible outputs (40

ohm pulldown, 60 ohm pullup)

•ODT and output drive strength auto‐calibration with

external resistor ZQ pin (120 ohm)

• Programmable termination and driver strength offsets

• Selectable external or internal VREF for data inputs;

programmable offsets for internal VREF

• Separate external VREF for address / command inputs

•Vendor ID, FIFO depth and Density info fields for

identification

• x32/x16 mode configuration set at power‐up with EDC

•Mirror function with MF pin

• Boundary scan function with SEN pin

•1.6V / 1.5V +/‐ 0.045V supply for device operation

(VDD)

•1.6V / 1.5V +/‐ 0.045V supply for I/O interface (VDDQ)

• 170 ball BGA package

FUNCTIONAL DESCRIPTION

The GDDR5 SGRAM is a high speed dynamic

random‐access memory designed for applications

requiring high bandwidth. GDDR5 devices contain

the following number of bits:

1 Gb has 1,073,741,824 bits and sixteen banks

The GDDR5 SGRAM uses a 8n prefetch

architecture and DDR interface to achieve high‐

speed operation. The device can be configured to

operate in x32 mode or x16 (clamshell) mode. The

mode is detected during device initialization. The

GDDR5 interface transfers two 32 bit wide data

words per WCK clock cycle to/from the I/O pins.

Corresponding to the 8n‐prefetch a single write or

read access consists of a 256 bit wide, two CK clock

cycle data transfer at the internal memory core and

eight corresponding 32 bit wide one‐half WCK clock

cycle data transfers at the I/O pins.

The GDDR5 SGRAM operates from a differential

clock CK and CK#. Commands are registered at

every rising edge of CK. Addresses are registered at

every rising edge of CK and every rising edge of

CK#.

GDDR5 replaces the pulsed strobes (WDQS &

RDQS) used in previous DRAMs such as GDDR4

with a free running differential forwarded clock

(WCK/WCK#) with both input and output data

registered and driven respectively at both edges of

the forwarded WCK.

Read and write accesses to the GDDR5 SGRAM are

burst oriented; an access starts at a selected location

and consists of a total of eight data words. Accesses

begin with the registration of an ACTIVE command,

which is then followed by a READ or WRITE

command. The address bits registered coincident

with the ACTIVE command and the next rising CK#

edge are used to select the bank and the row to be

accessed. The address bits registered coincident

with the READ or WRITE command and the next

rising CK# edge are used to select the bank and the

column location for the burst access.

H5GQ1H24AFR-R0C 数据表(PDF) 5 Page - Hynix Semiconductor

H5GQ1H24AFR-R0C 数据表(HTML) 5 Page - Hynix Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载