PIC12F675T-ESLASHP datasheet(65/136 Pages) MICROCHIP

65 / 136 page

 2010 Microchip Technology Inc.

DS41190G-page 65

PIC12F629/675

9.4.1

GP2/INT INTERRUPT

External interrupt on GP2/INT pin is edge-triggered;

either rising if INTEDG bit (OPTION<6>) is set, of

falling, if INTEDG bit is clear. When a valid edge

appears on the GP2/INT pin, the INTF bit (INT-

CON<1>) is set. This interrupt can be disabled by

clearing the INTE control bit (INTCON<4>). The INTF

bit must be cleared in software in the Interrupt Service

Routine before re-enabling this interrupt. The GP2/INT

interrupt can wake-up the processor from Sleep if the

INTE bit was set prior to going into Sleep. The status of

the GIE bit decides whether or not the processor

branches to the interrupt vector following wake-up. See

Section 9.7 “Power-Down Mode (Sleep)” for details

on Sleep and Figure 9-13 for timing of wake-up from

Sleep through GP2/INT interrupt.

9.4.2

TMR0 INTERRUPT

An overflow (FFh

 00h) in the TMR0 register will

set the T0IF (INTCON<2>) bit. The interrupt can

enabled/disabled

setting/clearing

T0IE

(INTCON<5>) bit. For operation of the Timer0 module,

see Section 4.0 “Timer0 Module”.

9.4.3

GPIO INTERRUPT

An input change on GPIO change sets the GPIF

(INTCON<0>) bit. The interrupt can be enabled/

disabled by setting/clearing the GPIE (INTCON<3>)

bit. Plus individual pins can be configured through the

IOC register.

9.4.4

COMPARATOR INTERRUPT

See

Section 6.9

“Comparator

Interrupts”

for

description of comparator interrupt.

9.4.5

A/D CONVERTER INTERRUPT

After a conversion is complete, the ADIF flag (PIR<6>)

is set. The interrupt can be enabled/disabled by setting

or clearing ADIE (PIE<6>).

See Section 7.0 “Analog-to-Digital Converter (A/D)

Module (PIC12F675 only)” for operation of the A/D

converter interrupt.

FIGURE 9-11:

INT PIN INTERRUPT TIMING

Note:

The ANSEL (9Fh) and CMCON (19h)

registers must be initialized to configure an

analog channel as a digital input. Pins

configured as analog inputs will read ‘0’.

The ANSEL register is defined for the

PIC12F675.

Note:

If a change on the I/O pin should occur

when the read operation is being executed

(start of the Q2 cycle), then the GPIF

interrupt flag may not get set.

Q3 Q4

OSC1

CLKOUT

INT pin

INTF Flag

(INTCON<1>)

GIE bit

(INTCON<7>)

INSTRUCTION FLOW

Instruction

Fetched

Instruction

Executed

Interrupt Latency

PC + 1

0004h

0005h

Inst (0004h)

Inst (0005h)

Dummy Cycle

Inst (PC)

Inst (PC+1)

Inst (PC - 1)

Inst (0004h)

Dummy Cycle

Inst (PC)

—

Note 1: INTF flag is sampled here (every Q1).

2: Asynchronous interrupt latency = 3-4 TCY. Synchronous latency = 3 TCY, where TCY = instruction cycle time. Latency

is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.

3: CLKOUT is available only in RC Oscillator mode.

4: For minimum width of INT pulse, refer to AC specs.

5: INTF is enabled to be set any time during the Q4-Q1 cycles.

PIC12F675T-E/P 数据表(PDF) 65 Page - Microchip Technology

PIC12F675T-E/P 数据表(HTML) 65 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载