ENC28J60-CSLASHSP datasheet(71/96 Pages) MICROCHIP

71 / 96 page

Preliminary

DS39662B-page 69

ENC28J60

12.1.5

LINK CHANGE INTERRUPT

FLAG (LINKIF)

The LINKIF indicates that the link status has changed.

The actual current link status can be obtained from the

PHSTAT1.LLSTAT or PHSTAT2.LSTAT (see Register 3-5

and Register 3-6). Unlike other interrupt sources, the link

status change interrupt is created in the integrated PHY

module; additional steps must be taken to enable it.

By Reset default, LINKIF is never set for any reason. To

receive

it,

the

host

controller

must

set

the

PHIE.PLNKIE and PGEIE bits. After setting the two

PHY interrupt enable bits, the LINKIF bit will then

shadow the contents of the PHIR.PGIF bit. The PHY

only supports one interrupt, so the PGIF bit will always

be the same as the PHIR.PLNKIF bit (when both PHY

enable bits are set).

Once LINKIF is set, it can only be cleared by the host

controller or by a Reset. If the link change interrupt

is enabled

(EIE.LINKIE

EIE.INTIE

PHIE.PLNKIE = 1 and PHIE.PGEIE = 1), an interrupt

will be generated by driving the INT pin low. If the link

change interrupt is not enabled (EIE.LINKIE = 0,

EIE.INTIE = 0, PHIE.PLNKIE = 0 or PHIE.PGEIE = 0),

the host controller may poll the ENC28J60 for the

PHIR.PLNKIF bit and take appropriate action.

The LINKIF bit is read-only. Because reading from PHY

registers requires non-negligible time, the host controller

may instead set PHIE.PLNKIE and PHIE.PGEIE and

then poll the EIR.LINKIF bit. Performing an MII read on

the PHIR register will clear the LINKIF, PGIF and

PLNKIF bits automatically and allow for future link status

change interrupts. See Section 3.3 “PHY Registers”

for information on accessing the PHY registers.

12.1.6

DMA INTERRUPT FLAG (DMAIF)

The DMA interrupt indicates that the DMA module has

completed its memory copy or checksum calculation

(ECON1.DMAST has transitioned from ‘1’ to ‘0’). Addi-

tionally, this interrupt will be caused if the host controller

cancels a DMA operation by manually clearing the

DMAST bit. Once set, DMAIF can only be cleared by the

host controller or by a Reset condition. If the DMA

interrupt is enabled (EIE.DMAIE = 1 and EIE.INTIE = 1),

an interrupt is generated by driving the INT pin low. If the

DMA interrupt is not enabled (EIE.DMAIE = 0 or

EIE.INTIE = 0), the host controller may poll the

ENC28J60 for the DMAIF and take appropriate action.

Once processed, the host controller should use the BFC

command to clear the EIR.DMAIF bit.

12.1.7

RECEIVE PACKET PENDING

INTERRUPT FLAG (PKTIF)

The Receive Packet Pending Interrupt Flag (PKTIF) is

used to indicate the presence of one or more data pack-

ets in the receive buffer and to provide a notification

means for the arrival of new packets. When the receive

buffer has at least one packet in it, EIR.PKTIF will be set.

In other words, this interrupt flag will be set anytime the

Ethernet Packet Count register (EPKTCNT) is non-zero.

If the receive packet pending interrupt is enabled

(EIE.PKTIE = 1 and EIE.INTIE = 1), an interrupt will be

generated by driving the INT pin low whenever a new

packet is successfully received and written into the

receive buffer. If the receive packet pending interrupt is

not enabled (EIE.PKTIE = 0 or EIE.INTIE = 0), the host

controller will not be notified when new packets arrive.

However, it may poll the PKTIF bit and take appropriate

action.

The PKTIF bit can only be cleared by the host controller

or by a Reset condition. In order to clear PKTIF, the

EPKTCNT register must be decremented to ‘0’. See

Section 7.2 “Receiving Packets” for more informa-

tion about clearing the EPKTCNT register. If the last

data packet in the receive buffer is processed,

EPKTCNT will become zero and the PKTIF bit will

automatically be cleared.

ENC28J60-C/SP 数据表(PDF) 71 Page - Microchip Technology

ENC28J60-C/SP 数据表(HTML) 71 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

数据表下载