ENC28J60-CSLASHSP datasheet(10/96 Pages) MICROCHIP

10 / 96 page

ENC28J60

DS39662B-page 8

Preliminary

2.5

I/O Levels

The ENC28J60 is a 3.3V part; however, it was

designed to be easily integrated into 5V systems. The

SPI CS, SCK and SI inputs, as well as the RESET pin,

are all 5V tolerant. On the other hand, if the host

controller is operated at 5V, it quite likely will not be

within specifications when its SPI and interrupt inputs

are driven by the 3.3V CMOS outputs on the

ENC28J60. A unidirectional level translator would be

necessary.

An economical 74HCT08 (quad AND gate), 74ACT125

(quad 3-state buffer) or many other 5V CMOS chips

with TTL level input buffers may be used to provide the

necessary level shifting. The use of 3-state buffers

permits easy integration into systems which share the

SPI bus with other devices. Figure 2-5 and Figure 2-6

show example translation schemes.

FIGURE 2-5:

LEVEL SHIFTING USING

AND GATES

FIGURE 2-6:

LEVEL SHIFTING USING

3-STATE BUFFERS

2.6

LED Configuration

The LEDA and LEDB pins support automatic polarity

detection on Reset. The LEDs can be connected such

that the pin must source current to turn the LED on, or

alternately connected such that the pin must sink cur-

rent to turn the LED on. Upon system Reset, the

ENC28J60 will detect how the LED is connected and

begin driving the LED to the default state configured by

the PHLCON register. If the LED polarity is changed

while the ENC28J60 is operating, the new polarity will

not be detected until the next system Reset occurs.

LEDB is unique in that the connection of the LED is

automatically read on Reset and determines how to ini-

tialize the PHCON1.PDPXMD bit. If the pin sources

current to illuminate the LED, the bit is cleared on

Reset and the PHY defaults to half-duplex operation. If

the pin sinks current to illuminate the LED, the bit is set

on Reset and the PHY defaults to full-duplex operation.

Figure 2-7 shows the two available options. If no LED

is attached to the LEDB pin, the PDPXMD bit will reset

to an indeterminate value.

FIGURE 2-7:

LEDB POLARITY AND

RESET CONFIGURATION

OPTIONS

The LEDs can also be configured separately to control

their operating polarity (on or off when active), blink rate

and blink stretch interval. The options are controlled by

the LACFG3:LACFG0 and LBCFG3:LBCFG0 bits.

Typical values for blink stretch are listed in Table 2-1.

TABLE 2-1:

LED BLINK STRETCH

LENGTH

I/O

SCK

INT0

MCU

SCK

INT

ENC28J60

CLKOUT

OSC1

I/O

SCK

INT0

MCU

SCK

INT

ENC28J60

CLKOUT

OSC1

Stretch Length

Typical Stretch (ms)

TNSTRCH (normal)

TMSTRCH (medium)

TLSTRCH (long)

140

LEDB

+3.3V

Full-Duplex Operation:

PDPXMD = 1

LEDB

Half-Duplex Operation:

PDPXMD = 0

ENC28J60-C/SP 数据表(PDF) 10 Page - Microchip Technology

ENC28J60-C/SP 数据表(HTML) 10 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

数据表下载

链接网址

ENC28J60-C/SP 数据表(PDF) 10 Page - Microchip Technology

ENC28J60-C/SP 数据表(HTML) 10 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

数据表 下载

链接网址

数据表下载