ENC28J60-CSLASHSP datasheet(75/96 Pages) MICROCHIP

75 / 96 page

Preliminary

DS39662B-page 73

ENC28J60

14.0

POWER-DOWN

The ENC28J60 may be commanded to power-down

via the SPI interface. When powered down, it will no

longer be able to transmit and receive any packets.

To maximize power savings:

Turn

off

packet

reception

clearing

ECON1.RXEN.

Wait for any in-progress packets to finish being

received by polling ESTAT.RXBUSY. This bit

should be clear before proceeding.

Wait for any current transmissions to end by

confirming ECON1.TXRTS is clear.

Set ECON2.VRPS (if not already set).

Enter Sleep by setting ECON2.PWRSV. All

MAC,

MII

and

PHY

registers

become

inaccessible as a result. Setting PWRSV also

clears ESTAT.CLKRDY automatically.

In Sleep mode, all registers and buffer memory will

maintain their states. The ETH registers and buffer

memory will still be accessible by the host controller.

Additionally, the clock driver will continue to operate.

The

CLKOUT

function

will

unaffected

(see

Section 2.3 “CLKOUT Pin”).

When normal operation is desired, the host controller

must perform a slightly modified procedure:

Wake-up by clearing ECON2.PWRSV.

Wait at least 300

μs for the PHY to stabilize. To

accomplish the delay, the host controller may

poll ESTAT.CLKRDY and wait for it to become

set.

Restore

receive

capability

setting

ECON1.RXEN.

After leaving Sleep mode, there is a delay of many

milliseconds before a new link is established (assuming

an appropriate link partner is present). The host

controller may wish to wait until the link is established

before attempting to transmit any packets. The link

status

can

determined

polling

the

PHSTAT2.LSTAT bit. Alternatively, the link change

interrupt

may

used

enabled.

See

Section 12.1.5

“Link

Change

Interrupt

Flag

(LINKIF)” for additional details.

TABLE 14-1:

SUMMARY OF REGISTERS USED WITH POWER-DOWN

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Reset

Values

on page

ESTAT

INT

BUFER

LATECOL

—

RXBUSY

TXABRT

CLKRDY

ECON2

AUTOINC PKTDEC

PWRSV

rVRPS

—

—13

ECON1

TXRST

RXRST

DMAST

CSUMEN

TXRTS

RXEN

BSEL1

BSEL0

Legend: — = unimplemented, read as ‘0’, r = reserved bit. Shaded cells are not used for power-down.

ENC28J60-C/SP 数据表(PDF) 75 Page - Microchip Technology

ENC28J60-C/SP 数据表(HTML) 75 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

数据表下载