BQ28Z560-R1 datasheet(36/60 Pages) TI1

36 / 60 page

bq28z560-R1

SLUSBD3 – APRIL 2013

www.ti.com

The Lifetime Data logging function helps development and diagnosis with the bq28z560-R1. The bq28z560-R1

device logs the Lifetime Data as specified in the Lifetime Data and Lifetime Temp Samples data flash

subclasses. The data log recordings are controlled by the Lifetime Resolution data flash subclass.

The Lifetime Data Logging can be started by setting the IT_ENABLE bit and setting the Update Time register to a

non-zero value.

Once the Lifetime Data Logging function is enabled, the measured values are compared to what is already

stored in the data flash. If the measured value is higher than the maximum or lower than the minimum value

stored in the data flash by more than the Resolution set for at least one parameter, the entire data flash Lifetime

registers are updated after at least LTUpdateTime.

LTUpdateTime sets the minimum update time between DF writes. When a new max/min is detected, an LT

Update window of 60 seconds is enabled and the DF writes occur at the end of this window. Any additional

max/min value detected within this window will also be updated. The first new max/min value detected after this

window will trigger the next LT Update window.

Internal to bq28z560-R1 is a RAM max/min table in addition to the DF max/min table. The RAM table is updated

independent of the resolution parameters. The DF table is updated only if at least one of the RAM parameters

exceeds the DF value by more than the resolution associated with it. When DF is updated, the entire RAM table

is written to DF. Consequently, it is possible to see a new max/min value for a certain parameter even if the

value of this parameter never exceeds the maximum or minimum value stored in the data flash for this parameter

value by the resolution amount.

The Lifetime Data Logging of one or more parameters can be reset or restarted by writing new default (or

starting) values to the corresponding data flash registers through sealed or unsealed access as described below.

However, when using unsealed access, new values will only take effect after device reset.

The logged data can be accessed as R/W in UNSEALED mode from the Lifetime Data SubClass (SubClass

ID=59) of data flash. Lifetime Data may be accessed (R/W) when sealed using a process identical in

Manufacturer Info Block B and C. The DataFlashBlock command code is 4.

NOTE

Only the first 32 bytes of Lifetime Data (not resolution parameters) can be R/W when

sealed. See MANUFACTURER INFORMATION BLOCKS for sealed access.

The logging settings such as Temperature Resolution, Voltage Resolution, Current Resolution, and Update Time

can be configured only in UNSEALED mode by writing to the Lifetime Resolution subclass (SubClassID=66) of

the data flash.

The Lifetime resolution registers contain the parameters that set the limits related to how much a data parameter

must exceed the previously logged Max/Min value to be updated in the lifetime log. For example, V must exceed

MaxV by more than Voltage Resolution to update MaxV in the data flash.

DETAILED CONFIGURATION REGISTER DESCRIPTIONS

The Pack Configuration Register

Some bq28z560-R1 pins are configured via the Pack Configuration data flash register, as indicated in Table 15.

This register is programmed/read via the methods described in ACCESSING THE DATA FLASH. The register is

located at subclass = 64, offset = 0.

Table 15. Pack Configuration Bit Definition

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

High Byte

RESCAP

CalEn

RSVD

IWAKE

RSNS1

RSNS0

Low Byte

GNDSEL

RESFACTSTEP

SLEEP

RMFCC

CLR_READ

ALRT_POL

RSVD

TEMPS

Submit Documentation Feedback

Product Folder Links: bq28z560-R1

BQ28Z560-R1 数据表(PDF) 36 Page - Texas Instruments

BQ28Z560-R1 数据表(HTML) 36 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

数据表下载