PIC16F72SLASHML datasheet(8/136 Pages) MICROCHIP

8 / 136 page

PIC16F72

DS39597B-page 6

 2002 Microchip Technology Inc.

TABLE 1-1:

PIC16F72 PINOUT DESCRIPTION

Pin Name

PDIP,

SOIC,

SSOP

Pin#

MLF

Pin#

I/O/P

Type

Buffer

Type

Description

OSC1/CLKI

ST/CMOS(3) Oscillator crystal input/external clock source input.

OSC2/CLKO

—

Oscillator crystal output. Connects to crystal or resonator in Crystal

Oscillator mode. In RC mode, the OSC2 pin outputs CLKO, which has

1/4 the frequency of OSC1, and denotes the instruction cycle rate.

MCLR/VPP

I/P

Master Clear (Reset) input or programming voltage input. This pin is

an active low RESET to the device.

PORTA is a bi-directional I/O port.

RA0/AN0

I/O

TTL

RA0 can also be analog input0.

RA1/AN1

I/O

TTL

RA1 can also be analog input1.

RA2/AN2

I/O

TTL

RA2 can also be analog input2.

RA3/AN3/VREF

I/O

TTL

RA3 can also be analog input3 or analog reference voltage.

RA4/T0CKI

I/O

RA4 can also be the clock input to the Timer0 module. Output is

open drain type.

RA5/AN4/SS

I/O

TTL

RA5 can also be analog input4 or the slave select for the

synchronous serial port.

PORTB is a bi-directional I/O port. PORTB can be software

programmed for internal weak pull-up on all inputs.

RB0/INT

I/O

TTL/ST(1)

RB0 can also be the external interrupt pin.

RB1

I/O

TTL

RB2

I/O

TTL

RB3

I/O

TTL

RB4

I/O

TTL

Interrupt-on-change pin.

RB5

I/O

TTL

Interrupt-on-change pin.

RB6/PGC

I/O

TTL/ST(2)

Interrupt-on-change pin. Serial programming clock.

RB7/PGD

I/O

TTL/ST(2)

Interrupt-on-change pin. Serial programming data.

PORTC is a bi-directional I/O port.

RC0/T1OSO/

T1CKI

I/O

RC0 can also be the Timer1 oscillator output or Timer1 clock input.

RC1/T1OSI

I/O

RC1 can also be the Timer1 oscillator input.

RC2/CCP1

I/O

RC2 can also be the Capture1 input/Compare1 output/

PWM1 output.

RC3/SCK/SCL

I/O

RC3 can also be the synchronous serial clock input/output for both

SPI and I2C modes.

RC4/SDI/SDA

I/O

RC4 can also be the SPI Data In (SPI mode) or

Data I/O (I2C mode).

RC5/SDO

I/O

RC5 can also be the SPI Data Out (SPI mode).

RC6

I/O

RC7

I/O

VSS

8, 19

5, 16

—

Ground reference for logic and I/O pins.

VDD

—

Positive supply for logic and I/O pins.

Legend: I = input

O = output

I/O = input/output

P = power

— = Not used

TTL = TTL input

ST = Schmitt Trigger input

Note

1: This buffer is a Schmitt Trigger input when configured as the external interrupt.

2: This buffer is a Schmitt Trigger input when used in Serial Programming mode.

3: This buffer is a Schmitt Trigger input when configured in RC Oscillator mode and a CMOS input otherwise.

PIC16F72/ML 数据表(PDF) 8 Page - Microchip Technology

PIC16F72/ML 数据表(HTML) 8 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载