LPC2917 datasheet(39/68 Pages) PHILIPS

39 / 68 page

LPC2917_19_1

Preliminary data sheet

Rev. 1.01 — 15 November 2007

39 of 68

NXP Semiconductors

LPC2917/19

ARM9 microcontroller with CAN and LIN

8.7.6.4

Master and slave mode

A PWM module can provide synchronization signals to other modules (also called Master

mode). The signal sync_out is a pulse of one clock cycle generated when the internal

PWM counter (re)starts. The signal trans_enable_out is a pulse synchronous to sync_out,

generated if a transfer from system registers to PWM shadow registers occurred when the

PWM counter restarted. A delay may be inserted between the counter start and

generation of trans_enable_out and sync_out.

A PWM module can use input signals trans_enable_in and sync_in to synchronize its

internal PWM counter and the transfer of shadow registers (Slave mode).

8.7.6.5

PWM pin description

Each of the four PWM modules in the MSCSS has the following pins. These are combined

with other functions on the port pins of the LPC2917/19. Table 21 shows the PWM0 to

PWM3 pins.

8.7.6.6

PWM clock description

The PWM modules are clocked by CLK_MSCSS_PWMx (x = 0-3), see Section 7.2.2.

Note that each PWM has its own CLK_MSCSS_PWMx branch clock for power

management. The frequency of all these clocks is identical to CLK_MSCSS_VPB since

they are derived from the same base clock BASE_MSCSS_CLK.

Also note that unlike the timer modules in the Peripheral SubSystem, the actual timer

counter registers of the PWM modules run at the same clock as the VPB system interface

CLK_MSCSS_VPB. This clock is independent of the AHB system clock.

If a PWM module is not used its CLK_MSCSS_PWMx branch clock can be switched off.

8.7.7 Timers in the MSCSS

8.7.7.1

Overview

The two timers in the MSCSS are functionally identical to the timers in the peripheral

subsystem, see Section 8.4.3. The features of the timers in the MSCSS are the same as

the timers in the peripheral subsystem, but the capture inputs and match outputs are not

available on the device pins. These signals are instead connected to the ADC and PWM

modules as outlined in the description of the MSCSS, see Section 8.7.2.

Table 21.

PWM pins

Symbol

Direction

Description

PWMn CAP[0]

PWM n capture input 0

PWMn CAP[1]

PWM n capture input 1

PWMn CAP[2]

PWM n capture input 2

PWMn MAT[0]

out

PWM n match output 0

PWMn MAT[1]

out

PWM n match output 1

PWMn MAT[2]

out

PWM n match output 2

PWMn MAT[3]

out

PWM n match output 3

PWMn MAT[4]

out

PWM n match output 4

PWMn MAT[5]

out

PWM n match output 5

PWMn TRAP

PWM n trap input

LPC2917 数据表(PDF) 39 Page - NXP Semiconductors

LPC2917 数据表(HTML) 39 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

数据表下载