LPC2917 datasheet(62/68 Pages) PHILIPS

62 / 68 page

LPC2917_19_1

Preliminary data sheet

Rev. 1.01 — 15 November 2007

62 of 68

NXP Semiconductors

LPC2917/19

ARM9 microcontroller with CAN and LIN

[1]

For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026); order a copy from your NXP

Semiconductors sales office.

[2]

All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with

respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of

the moisture in them (the so called popcorn effect).

[3]

For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board.

[4]

Hot bar soldering or manual soldering is suitable for PMFP packages.

[5]

These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account be processed

through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature exceeding 217

°C ± 10 °C

measured in the atmosphere of the reflow oven. The package body peak temperature must be kept as low as possible.

[6]

These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate

between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the

heatsink surface.

[7]

If wave soldering is considered, then the package must be placed at a 45

° angle to the solder wave direction. The package footprint

must incorporate solder thieves downstream and at the side corners.

[8]

Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for

packages with a pitch (e) equal to or smaller than 0.65 mm.

[9]

Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely

not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.

[10] Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered pre-mounted on flex foil.

However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate

soldering profile can be provided on request.

Surface mount

BGA, HTSSON..T[5], LBGA,

LFBGA, SQFP, SSOP..T[5],

TFBGA, VFBGA, XSON

not suitable

suitable

−

DHVQFN, HBCC, HBGA, HLQFP,

HSO, HSOP, HSQFP, HSSON,

HTQFP, HTSSOP, HVQFN,

HVSON, SMS

not suitable[6]

suitable

−

PLCC[7], SO, SOJ

suitable

−

LQFP, QFP, TQFP

not recommended[7][8]

suitable

−

SSOP, TSSOP, VSO, VSSOP

not recommended[9]

suitable

−

CWQCCN..L[10], WQCCN..L[10]

not suitable

−

Table 34.

Suitability of IC packages for wave, reflow and dipping soldering methods …continued

Mounting

Package[1]

Soldering method

Wave

Reflow[2]

Dipping

LPC2917 数据表(PDF) 62 Page - NXP Semiconductors

LPC2917 数据表(HTML) 62 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

数据表下载

链接网址

LPC2917 数据表(PDF) 62 Page - NXP Semiconductors

LPC2917 数据表(HTML) 62 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

数据表 下载

链接网址

数据表下载