H8SSLASH2225 datasheet(248/1071 Pages) RENESAS

248 / 1071 page

Section 6 PC Break Controller (PBC)

Rev. 5.00 Aug 08, 2006 page 162 of 982

REJ09B0054-0500

• When the SLEEP instruction causes a transition to software standby mode or watch mode:

After execution of the SLEEP instruction, a transition is made to the respective mode, and PC

break interrupt handling is not executed. However, the CMFA or CMFB flag is set (figure 6.2

(D).

SLEEP instruction

execution

High-speed

(medium-speed)

mode

SLEEP instruction

execution

Subactive

mode

System clock

→ subclock

Direct transition

exception handling

PC break exception

handling

Execution of instruction

after sleep instruction

Subclock

→

system clock,

oscillation settling time

SLEEP instruction

execution

Transition to

respective mode

Direct transition

exception handling

PC break exception

handling

Execution of instruction

after sleep instruction

PC break exception

handling

Execution of instruction

after sleep instruction

(A)

(B)

(C)

(D)

SLEEP instruction

execution

Figure 6.2 Operation in Power-Down Mode Transitions

6.3.5

When Instruction Execution Is Delayed by One State

While the break interrupt enable bit is set to 1, instruction execution is one state later than usual.

• For 1-word branch instructions (Bcc d:8, BSR, JSR, JMP, TRAPA, RTE, and RTS) in on-chip

ROM or RAM.

• When break interruption by instruction fetch is set, the set address indicates on-chip ROM or

RAM space, and that address is used for data access, the instruction that executes the data

access is one state later than in normal operation.

• When break interruption by instruction fetch is set and a break interrupt is generated, if the

executing instruction immediately preceding the set instruction has one of the addressing

modes shown below, and that address indicates on-chip ROM or RAM, the instruction will be

one state later than in normal operation.

Addressing modes: @ERn, @(d:16,ERn), @(d:32,ERn), @-ERn/ERn+, @aa:8, @aa:24,

@aa:32, @(d:8,PC), @(d:16,PC), @@aa:8

• When break interruption by instruction fetch is set and a break interrupt is generated, if the

executing instruction immediately preceding the set instruction is NOP or SLEEP, or has #xx,

H8S/2225 数据表(PDF) 248 Page - Renesas Technology Corp

H8S/2225 数据表(HTML) 248 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

H8S/2225 数据表(PDF) 248 Page - Renesas Technology Corp

H8S/2225 数据表(HTML) 248 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载