| 数据搜索系统,热门电子元器件搜索 |
|
ST7MC1 数据表(PDF) 198 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST7MC1 数据表(HTML) 198 Page - STMicroelectronics |
|
198 / 308 page ![]() ST7MC1/ST7MC2 198/308 MOTOR CONTROLLER (Cont’d) 10.6.9.4 Programmable Chopper Depending on the application hardware (use of a pulse transformer, for example), a chopper may be needed for the PWM signal. The MREF register al- lows the chopping frequency and mode to be pro- grammed. The HFE[1:0] bits program the channels on which chopping is to be applied. The chopped PWM sig- nal may be needed for high side switches only, low side switches or both of them in the same time (see Table 54). Table 54. Chopping mode The chopping frequency can any of the 8 values from 100KHz to 2MHz selected by the HFRQ[2:0] bits in the MREF register (see Table 55). Table 55. Chopping frequency Note: When the PCN bit = 0: – If complementary PWM signals are not applied (DTE bit = 0), the high and low drivers are fixed by the MPAR register. Figure 108, Figure 114 and Figure 115 indicate where the HFE[1:0] bits are taken into account depending on the PWM application. – If complementary PWM signals are applied (DTE bit = 1), the channels are paired as explained in “Dead Time Generator” on page 193. This means that the high and low channels are fixed and the HFE[1:0] bits indicate where to apply the chopper. Figure 116 shows typical complemen- tary PWM signals with high frequency chopping enabled on both high and low drivers. Figure 116. Complementary PWM signals with chopping frequency on high and low side drivers HFE[1:0] bits Chopping mode HFE1 HFE0 PCN bit =0 PCN bit =1 00 OFF OFF 0 1 Low channels only Low side switches MCO1, 3, 5 1 0 High channels only High side switches MCO0, 2, 4 11 Both Low and High channels Both high and low sides HFRQ2 HFRQ1 HFRQ0 Chopping frequency Fmtc = 16MHz Fmtc = 8MHz Chopping frequency Fmtc = 4MHz 0 0 0 100 KHz 50 KHz 0 0 1 200 KHz 100 KHz 0 1 0 400 KHz 200 KHz 0 1 1 500 KHz 250 KHz 1 0 0 800 KHz 400 KHz 1 0 1 1 MHz 500 KHz 1 1 0 1.33 MHz 666.66 MHz 11 1 2 MHz 1 MHz Reference Output A Output B Delay Delay 5V 5V 5V 0V 0V 0V Input signal 1 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |