DS31256 datasheet(104/183 Pages) MAXIM

104 / 183 page

DS31256 256-Channel, High-Throughput HDLC Controller

104 of 183

- FOR DMA USE ONLY/HOST CAN ONLY READ THIS FIELD -

dword 2; Bits 16 to 28/Byte Count. The DMA uses these 13 bits to keep track of the number of bytes stored in

the data buffer. Maximum is 8188 Bytes (0000h = 0 Bytes / 1FFCh = 8188 Bytes).

- FOR DMA USE ONLY/HOST CAN ONLY READ THIS FIELD -

dword 2; Bits 29 to 31/Threshold Count. These bits keep track of the number of data buffers that have been

filled so that the receive DMA knows when, based on the host-controlled threshold, to write to the done queue.

000 = threshold count is 0 data buffers

001 = threshold count is 1 data buffer

010 = threshold count is 2 data buffers

011 = threshold count is 3 data buffers

100 = threshold count is 4 data buffers

101 = threshold count is 5 data buffers

110 = threshold count is 6 data buffers

111 = threshold count is 7 data buffers

RDMACIS

Receive DMA Channel Configuration Indirect Select

0770h

Bit #

Name

HCID7

HCID6

HCID5

HCID4

HCID3

HCID2

HCID1

HCID0

Default

Bit #

Name

IAB

IARW

n/a

RDCW2

RDCW1

RDCW0

Default

Note: Bits that are underlined are read-only; all other bits are read-write.

Bits 0 to 7/HDLC Channel ID (HCID0 to HCID7)

00000000 (00h) = HDLC channel number 1

11111111 (FFh) = HDLC channel number 256

Bits 8 to 10/Receive DMA Configuration RAM Word Select Bits 0 to 2 (RDCW0 to RDCW2)

000 = lower word of dword 0

001 = upper word of dword 0

010 = lower word of dword 1

011 = upper word of dword 1

100 = lower word of dword 2 (only word that the host can write to)

101 = upper word of dword 2

110 = illegal state

111 = illegal state

Bit 14/Indirect Access Read/Write (IARW). When the host wishes to read data from the internal receive DMA

configuration RAM, this bit should be written to 1 by the host. This causes the device to begin obtaining the data

from the channel location indicated by the HCID bits. During the read access, the IAB bit is set to 1. Once the data

is ready to be read from the RDMAC register, the IAB bit is set to 0. When the host wishes to write data to the

internal receive DMA configuration RAM, this bit should be written to 0 by the host. This causes the device to

take the data that is currently present in the RDMAC register and write it to the channel location indicated by the

HCID bits. When the device has completed the write, the IAB bit is set to 0.

Bit 15/Indirect Access Busy (IAB). When an indirect read or write access is in progress, this read-only bit is set

to 1. During a read operation, this bit is set to 1 until the data is ready to be read. It is set to 0 when the data is

DS31256 数据表(PDF) 104 Page - Maxim Integrated Products

DS31256 数据表(HTML) 104 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载