ST92F120JR9T datasheet(87/320 Pages) STMICROELECTRONICS

87 / 320 page

87/320

ST92F120 - INTERRUPTS

WAKE-UP / INTERRUPT LINES MANAGEMENT UNIT (Cont’d)

5.11.3 Functional Description

5.11.3.1 Interrupt Mode

To configure the 16 wake-up lines as interrupt

sources, use the following procedure:

1. Configure the mask bits of the 16 wake-up lines

(WUMRL, WUMRH)

2. Configure the triggering edge registers of the

wake-up lines (WUTRL, WUTRH)

3. Set bit 7 of EIMR (R244 Page 0) and EITR

(R242 Page 0) registers of the CPU: so an

interrupt coming from one of the 16 lines can be

correctly acknowledged

4. Reset the WKUP-INT bit in the WUCTRL regis-

ter to disable Wake-up Mode

5. Set the ID1S bit in the WUCTRL register to dis-

able the INT7 external interrupt source and

enable the 16 wake-up lines as external inter-

rupt source lines.

To return to standard mode (INT7 external inter-

rupt source enabled and 16 wake-up lines disa-

bled) it is sufficient to reset the ID1S bit.

5.11.3.2 Wake-up Mode Selection

To configure the 16 lines as wake-up sources, use

the following procedure:

1. Configure the mask bits of the 16 wake-up lines

(WUMRL, WUMRH).

2. Configure the triggering edge registers of the

wake-up lines (WUTRL, WUTRH).

3. Set, as for Interrupt Mode selection, bit 7 of

EIMR and EITR registers only if an interrupt

routine is to be executed after a wake-up event.

Otherwise, if the wake-up event only restarts

the execution of the code from where it was

stopped, the INTD1 interrupt channel must be

masked or the external source must be

selected by resetting the ID1S bit.

4. Since the RCCU can generate an interrupt

request when exiting from STOP mode, take

care to mask it even if the wake-up event is

only to restart code execution.

5. Set the WKUP-INT bit in the WUCTRL register

to select Wake-up Mode

6. Set the ID1S bit in the WUCTRL register to dis-

able the INT7 external interrupt source and

enable the 16 wake-up lines as external inter-

rupt source lines. This is not mandatory if the

wake-up event does not require an interrupt

response.

7. Write the sequence 1,0,1 to the STOP bit of the

WUCTRL register with three consecutive write

operations. This is the STOP bit setting

sequence.

To detect if STOP Mode was entered or not, im-

mediately after the STOP bit setting sequence,

poll the RCCU EX_STP bit (R242.7, Page 55) and

the STOP bit itself.

5.11.3.3 STOP Mode Entry Conditions

Assuming the ST9 is in Run mode: during the

STOP bit setting sequence the following cases

may occur:

Case 1: NMI = 0, wrong STOP bit setting se-

quence

This can happen if an Interrupt/DMA request is ac-

knowledged during the STOP bit setting se-

quence. In this case polling the STOP and

EX_STP bits will give:

STOP = 0, EX_STP = 0

This means that the ST9 did not enter STOP mode

due to a bad STOP bit setting sequence: the user

must retry the sequence.

Case 2: NMI = 0, correct STOP bit setting se-

quence

In this case the ST9 enters STOP mode. There are

two ways to exit STOP mode:

1. A wake-up interrupt (not an NMI interrupt) is

acknowledged. That implies:

STOP = 0, EX_STP = 1

This means that the ST9 entered and exited STOP

mode due to an external wake-up line event.

2. A NMI rising edge woke up the ST9. This

implies:

STOP = 1, EX_STP = 1

This means that the ST9 entered and exited STOP

mode due to an NMI (rising edge) event. The user

should clear the STOP bit via software.

ST92F120JR9T 数据表(PDF) 87 Page - STMicroelectronics

ST92F120JR9T 数据表(HTML) 87 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载