AM79C978VCSLASHW datasheet(108/261 Pages) AMD

108 / 261 page

108

Am79C978

PCI Expansion ROM Base Address Register

Offset 30h

The PCI Expansion ROM Base Address register is a

32-bit register that defines the base address, size, and

address alignment of an Expansion ROM. It is located

at offset 30h in the PCI Configuration Space.

Bit

Name

Description

31-20

ROMBASE Expansion ROM base address

most significant 12 bits. These

bits are written by the host to

specify the location of the Expan-

sion ROM in all of memory space.

ROMBASE must be written with a

valid

address

before

the

Am79C978 Expansion ROM ac-

cess

enabled

setting

ROMEN (PCI Expansion ROM

Base Address register, bit 0) and

MEMEN (PCI Command register,

bit 1).

Since the 12 most significant bits

of the base address are program-

mable, the host can map the Ex-

pansion

ROM

any

boundary.

When the Am79C978 controller

is enabled for Expansion ROM

access (ROMEN and MEMEN

are set to 1), it monitors the PCI

bus for a valid memory com-

mand. If the value on AD[31:2]

during the address phase of the

cycle falls between ROMBASE

and ROMBASE + 1M - 4, the

Am79C978 controller will drive

DEVSEL indicating it will respond

to the access.

ROMBASE is read and written by

the host. ROMBASE is cleared

by H_RESET and is not affected

by S_RESET or by setting the

STOP bit.

19-1

ROMSIZE

ROM size. Read as zeros; write

operation have no effect. ROM-

SIZE indicates the maximum size

the

Expansion

ROM

the

Am79C978 controller can sup-

port. The host can determine the

Expansion ROM size by writing

FFFF FFFFh to the Expansion

ROM Base Address register. It

will read back a value of 0 in bit

19-1, indicating an Expansion

ROM size of 1M.

Note that ROMSIZE only speci-

fies the maximum size of Expan-

sion

ROM

the

Am79C978

controller supports. A smaller

ROM can also be used. The actu-

al size of the code in the Expan-

sion ROM is always determined

by reading the Expansion ROM

header.

ROMEN

Expansion ROM Enable. Written

by the host to enable access to

the

Expansion

ROM.

The

Am79C978 controller will only re-

spond to accesses to the Expan-

sion ROM when both ROMEN

and MEMEN (PCI Command reg-

ister, bit 1) are set to 1.

ROMEN is read and written by

the host. ROMEN is cleared by

H_RESET and is not effected by

S_RESET or by setting the STOP

bit.

PCI Capabilities Pointer Register

Offset 34h

Bit

Name

Description

7-0

CAP_PTR

The PCI Capabilities Pointer reg-

ister is an 8-bit register that points

to a linked list of capabilities im-

plemented on this device. This

40h.

The PCI Capabilities Pointer reg-

ister is located at offset 34h in the

PCI Configuration Space. It is

read only.

PCI Interrupt Line Register

Offset 3Ch

The PCI Interrupt Line register is an 8-bit register that

is used to communicate the routing of the interrupt.

This register is written by the POST software as it ini-

tializes the Am79C978 controller in the system. The

interrupt channel which the POST software has as-

signed to the Am79C978 controller. The PCI Interrupt

Line register is not modified by the Am79C978 control-

ler. It has no effect on the operation of the device.

The PCI Interrupt Line register is located at offset 3Ch

in the PCI Configuration Space. It is read and written by

AM79C978VC/W 数据表(PDF) 108 Page - Advanced Micro Devices

AM79C978VC/W 数据表(HTML) 108 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载