USB3320 datasheet(42/70 Pages) MICROCHIP

42 / 70 page

USB3320

DS00001792B-page 42

 2014-2015 Microchip Technology Inc.

In Figure 6-8 the transceiver asserts DIR to take control of the data bus from the Link. The assertion of DIR and NXT in

the same cycle contains additional information that Rxactive has been asserted. When NXT is de-asserted and DIR is

asserted, the RXCMD data is transferred to the Link. After the last byte of the USB receive packet is transferred to the

transceiver, the linestate will return to idle.

The ULPI full speed receiver operates according to the UTMI / ULPI specification. In the full speed case, the NXT signal

will assert only when the Data bus has a valid received data byte. When NXT is low with DIR high, the RXCMD is driven

on the data bus.

In full speed, the USB3320 will not issue a Rxactive de-assertion in the RXCMD until the DP/DM linestate transitions to

idle. This prevents the Link from violating the two full speed bit times minimum turn around time.

6.2.5.1

Disconnect Detection

A High Speed host must detect a disconnect by sampling the transmitter outputs during the long EOP transmitted during

a SOF packet. The USB3320 only looks for a high speed disconnect during the long EOP where the period is long

enough for the disconnect reflection to return to the host transceiver. When a high speed disconnect occurs, the

USB3320 will return a RXCMD and set the host disconnect bit in the USB Interrupt Status register.

When in FS or LS modes, the Link is expected to handle all disconnect detection.

6.3

Low Power Mode

Low Power Mode is a power down state to save current when the USB session is suspended. The Link controls when

the transceiver is placed into or out of Low Power Mode. In Low Power Mode all of the circuits are powered down except

the interface pins, full speed receiver, VBUS comparators, and IdGnd comparator.

Before entering Low Power Mode, the USB3320 must be configured to set the desired state of the USB transceiver. The

XcvrSelect[1:0]

, TermSelect and OpMode[1:0] bits in the Function Control register, and the DpPulldown and DmPull-

down

bits in the OTG Control register control the configuration as shown in Table 5-1. The DP and DM pins are config-

ured to a high impedance state by configuring OpMode[1:0] = 01. Pull-down resistors with a value of approximately 2MΩ

are present on the DP and DM pins to avoid false linestate indications that could result if the pins were allowed to float.

6.3.1

ENTERING LOW POWER/SUSPEND MODE

To enter Low Power Mode, the Link will write a 0 or clear the SuspendM bit in the Function Control register. After this

write is complete, the transceiver will assert DIR high and after a minimum of five rising edges of CLKOUT, drive the

clock low. After the clock is stopped, the transceiver will enter a low power state to conserve current. Placing the trans-

ceiver in Suspend Mode is not related to USB Suspend. To clarify this point, USB Suspend is initiated when a USB host

FIGURE 6-8:

ULPI RECEIVE IN SYNCHRONOUS MODE

DIR

CLK

DATA[7:0]

STP

NXT

Rxd

Cmd

Idle

Turn

around

PID

Rxd

Cmd

Turn

around

USB3320 数据表(PDF) 42 Page - Microchip Technology

USB3320 数据表(HTML) 42 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

数据表下载