ADAS1000-4BSTZ datasheet(63/80 Pages) AD

63 / 80 page

Data Sheet

ADAS1000-3/ADAS1000-4

Table 33. GPIO Control Register (GPIOCTL) Address 0x06, Reset Value = 0x000000

REE

Default

Bit

Name

Function

[23:19]

Reserved

Reserved, set to 0

R/W

SPIFW

Frame secondary SPI words with chip select

0 (default) =

MCSEE

asserted for entire frame

1 =

MCSEE

asserted for individual word

R/W

Reserved

Reserved, set to 0

R/W

SPIEN

Secondary SPI enable; SPI interface providing ECG data at 128 kHz data rate for external digital pace

algorithm detection, uses GPIO0, GPIO1, GPIO2 pins

0 (default) = disabled

1 = enabled; the individual control bits for GPIO0, GPIO1, GPIO2 are ignored; GPIO3 is not affected

by SPIEN

R/W

[15:14]

G3CTL [1:0]

State of GPIO3 pin

00 (default) = high impedance

01 = input

10 = output

11 = open drain

R/W

G3OUT

Output value to be written to GPIO3 when the pin is configured as an output or open drain

0 (default) = low value

1 = high value

G3IN

Read only; input value read from GPIO3 when the pin is configured as an input

0 (default) = low value

1 = high value

R/W

[11:10]

G2CTL [1:0]

State of GPIO2 pin

00 (default) = high impedance

01 = input

10 = output

11 = open drain

R/W

G2OUT

Output value to be written to GPIO2 when the pin is configured as an output or open drain

0 (default) = low value

1 = high value

G2IN

Read only Input value read from GPIO2 when the pin is configured as an input

0 (default) = low value

1 = high value

R/W

[7:6]

G1CTL [1:0]

State of GPIO1 pin

00 (default) = high impedance

01 = input

10 = output

11 = open drain

R/W

G1OUT

Output value to be written to GPIO1 when the pin is configured as an output or open drain

0 (default) = low value

1 = high value

G1IN

Read only; input value read from GPIO1 when the pin is configured as an input

0 (default) = low value

1 = high value

R/W

[3:2]

G0CTL [1:0]

State of the GPIO0 pin

00 (default) = high impedance

01 = input

10 = output

11 = open drain

R/W

G0OUT

Output value to be written to GPIO0 when the pin is configured as an output or open drain

0 (default) = low value

1 = high value

G0IN

(Read only) input value read from GPIO0 when the pin is configured as an input

0 (default) = low value

1 = high value

Rev. B | Page 63 of 80

ADAS1000-4BSTZ 数据表(PDF) 63 Page - Analog Devices

ADAS1000-4BSTZ 数据表(HTML) 63 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表下载

链接网址

ADAS1000-4BSTZ 数据表(PDF) 63 Page - Analog Devices

ADAS1000-4BSTZ 数据表(HTML) 63 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

数据表 下载

链接网址

数据表下载