ST92F120JR9T datasheet(232/320 Pages) STMICROELECTRONICS

232 / 320 page

232/320

I2C BUS INTERFACE

I2C INTERFACE (Cont’d)

10.7.7 Register Description

IMPORTANT:

1. To guarantee correct operation, before enabling

the peripheral (while I2CCR.PE=0), configure bit7

and bit6 of the I2COAR2 register according to the

internal clock INTCLK (for example 11xxxxxxb in

the range 14 - 30 MHz).

2. Bit7 of the I2CCR register must be cleared.

I2C CONTROL REGISTER (I2CCR)

R240 - Read / Write

Reset Value: 0000 0000 (00h)

Bit 7:6 = Reserved

Must be cleared

Bit 5 = PE

Peripheral Enable.

This bit is set and cleared by software.

0: Peripheral disabled (reset value)

1: Master/Slave capability

Notes:

– When I2CCR.PE=0, all the bits of the I2CCR

cept the STOP bit are reset. All outputs will be re-

leased while I2CCR.PE=0

– When I2CCR.PE=1, the corresponding I/O pins

are selected by hardware as alternate functions

(open drain).

– To enable the I2C interface, write the I2CCR reg-

ister TWICE with I2CCR.PE=1 as the first write

only activates the interface (only I2CCR.PE is

set).

– When PE=1, the FREQ[2:0] and EN10BIT bits in

the I2COAR2 and I2CADR registers cannot be

written. The value of these bits can be changed

only when PE=0.

Bit 4 = ENGC

General Call address enable.

Setting this bit the peripheral works as a slave and

the value stored in the I2CADR register is recog-

nized as device address.

This bit is set and cleared by software. It is also

cleared by hardware when the interface is disa-

bled (I2CCR.PE=0).

0: The address stored in the I2CADR register is

ignored (reset value)

1: The General Call address stored in the I2CADR

Note: The correct value (usually 00h) must be

written in the I2CADR register before enabling the

General Call feature.

Bit 3 = START

Generation of a Start condition.

This bit is set and cleared by software. It is also

cleared by hardware when the interface is disa-

bled (I2CCR.PE=0) or when the Start condition is

sent (with interrupt generation if ITE=1).

– In master mode:

0: No start generation

1: Repeated start generation

– In slave mode:

0: No start generation (reset value)

1: Start generation when the bus is free

Bit 2 = ACK

Acknowledge enable.

This bit is set and cleared by software. It is also

cleared by hardware when the interface is disa-

bled (I2CCR.PE=0).

0: No acknowledge returned (reset value)

1: Acknowledge returned after an address byte or

a data byte is received

Bit 1 = STOP

Generation of a Stop condition.

This bit is set and cleared by software. It is also

cleared by hardware in master mode. It is not

cleared

when

the

interface

disabled

(I2CCR.PE=0). In slave mode, this bit must be set

only when I2CSR1.BTF=1.

– In master mode:

0: No stop generation

1: Stop generation after the current byte transfer

or after the current Start condition is sent. The

STOP bit is cleared by hardware when the Stop

condition is sent.

– In slave mode:

0: No stop generation (reset value)

1: Release SCL and SDA lines after the current

byte transfer (I2CSR1.BTF=1). In this mode the

STOP bit has to be cleared by software.

ENGC

START ACK STOP ITE

ST92F120JR9T 数据表(PDF) 232 Page - STMicroelectronics

ST92F120JR9T 数据表(HTML) 232 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST92F120JR9T 数据表(PDF) 232 Page - STMicroelectronics

ST92F120JR9T 数据表(HTML) 232 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载