R8CSLASH2G datasheet(188/344 Pages) RENESAS

188 / 344 page

R8C/2G Group

17. Timers

Rev.1.00

Apr 04, 2008

Page 168 of 318

REJ09B0387-0100

17.2.2

Programmable Waveform Generation Mode

In programmable waveform generation mode, the signal output from the TRBO pin is inverted each time the

counter underflows, while the values in registers TRBPR and TRBSC are counted alternately (refer to Table

17.8 Programmable Waveform Generation Mode Specifications). Counting starts by counting the setting

value in the TRBPR register. The TRBOCR register is unused in this mode.

Figure 17.18 shows TRBIOC Register in Programmable Waveform Generation Mode. Figure 17.19 shows an

Operating Example of Timer RB in Programmable Waveform Generation Mode.

NOTES:

1. Even when counting the secondary period, the TRBPR register may be read.

2. The set values are reflected in the waveform output beginning with the following primary period after writing to

the TRBPR register.

3. The value written to the TOCNT bit is enabled by the following.

• When counting starts.

• When a timer RB interrupt request is generated.

The contents after the TOCNT bit is changed are reflected from the output of the following primary period.

Table 17.8

Programmable Waveform Generation Mode Specifications

Item

Specification

Count sources

f1, f2, f8, timer RA underflow

Count operations

• Decrement

• When the timer underflows, it reloads the contents of the primary reload and secondary

reload registers alternately before the count continues.

Width and period of

output waveform

Primary period: (n+1)(m+1)/fi

Secondary period: (n+1)(p+1)/fi

Period: (n+1){(m+1)+(p+1)}/fi

fi: Count source frequency

n: Value set in TRBPRE register

m: Value set in TRBPR register

p: Value set in TRBSC register

Count start condition

1 (count start) is written to the TSTART bit in the TRBCR register.

Count stop conditions

• 0 (count stop) is written to the TSTART bit in the TRBCR register.

• 1 (count forcibly stop) is written to the TSTOP bit in the TRBCR register.

Interrupt request

generation timing

In half a cycle of the count source, after timer RB underflows during the secondary period

(at the same time as the TRBO output change) [timer RB interrupt]

TRBO pin function

Programmable output port or pulse output

INT0 pin function

Programmable I/O port or INT0 interrupt input

Read from timer

The count value can be read out by reading registers TRBPR and TRBPRE.(1)

Write to timer

• When registers TRBPRE, TRBSC, and TRBPR are written while the count is stopped,

values are written to both the reload register and counter.

• When registers TRBPRE, TRBSC, and TRBPR are written to during count operation,

values are written to the reload registers only.(2)

Select functions

• Output level select function

The TOPL bit in the TRBIOC register selects the output level during primary and

secondary periods.

• TRBO pin output switch function

Timer RB pulse output or P3_1 (P1_3) latch output is selected by the TOCNT bit in the

TRBIOC register.(3)

• TRBO pin select function

P3_1 or P1_3 is selected by the TRBOSEL bit in the PINSR2 register.

R8C/2G 数据表(PDF) 188 Page - Renesas Technology Corp

R8C/2G 数据表(HTML) 188 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载