TNETV1644ZDU6 datasheet(185/306 Pages) TI1

185 / 306 page

6.5.3

Maximum Reset

TMS320DM6437

Digital Media Processor

www.ti.com

SPRS345D – NOVEMBER 2006 – REVISED JUNE 2008

At this point:

–

The I/O pins are controlled by the default peripherals (default peripherals are determined by

PINMUX0 and PINMUX1 registers).

–

The clock and reset of each peripheral is determined by the default settings of the Power and Sleep

Controller (PSC).

–

The PLL Controllers are operating in PLL Bypass Mode.

–

The C64x+ begins executing from DSPBOOTADDR (determined by bootmode selection).

After the reset sequence, the boot sequence begins. For more details on the boot sequence, see the

Using the TMS320DM643x Bootloader Application Report (literature number SPRAAG0)).

After the boot sequence, follow the software initialization sequence described in Section 3.8, Device

Initialization Sequence After Reset.

A Maximum (Max) Reset is initiated by the emulator or the watchdog timer (Timer 2). The effects are the

same as a warm reset, except the device boot and configuration pins are not re-latched. The emulator

initiates a maximum reset via the ICEPICK module. This ICEPICK initiated reset is non-maskable. When

the watchdog timer counter reaches zero, this will also initiate a maximum reset to recover from a runaway

condition. The watchdog timeout reset condition is masked if the TIMERCTL.WDRST bit is cleared to "0".

To invoke the maximum reset via the ICEPICK module, the user can perform the following from the Code

Composer Studio™ IDE menu: Debug

→Advanced Resets→System Reset

This is the Max Reset sequence:

1. Max Reset is initiated by the emulator or the watchdog timer.

During this time, the following happens:

–

The reset signals flow to the entire chip resetting all the modules on chip except the emulation

logic.

–

The PLL Controllers are reset thereby, switching back to PLL Bypass Mode and resetting all their

registers to default values. Both PLL1 and PLL2 are placed in reset and lose lock.

–

The RESETOUT pin becomes asserted (low), indicating the device is in reset.

2. After device initialization is complete, the PLL Controllers pause the system clocks for 10 cycles. At the

end of these 10 cycles, the RESETOUT pin is deasserted (driven high).

At this point:

–

The I/O pins are controlled by the default peripherals (default peripherals are determined by

PINMUX0 and PINMUX1 registers).

–

The clock and reset of each peripheral is determined by the default settings of the Power and Sleep

Controller (PSC).

–

The PLL Controllers are operating in PLL Bypass Mode.

–

The C64x+ begins executing from DSPBOOTADDR (determined by bootmode selection).

After the reset sequence, the boot sequence begins. Since the boot and configuration pins are not latched

with a Max Reset, the previous values (as shown in the BOOTCFG register) are used to select the boot

mode. For more details on the boot sequence, see the Using the TMS320DM643x Bootloader Application

Report (literature number SPRAAG0).

After the boot sequence, follow the software initialization sequence described in Section 3.8, Device

Initialization Sequence After Reset.

Submit Documentation Feedback

Peripheral Information and Electrical Specifications

185

TNETV1644ZDU6 数据表(PDF) 185 Page - Texas Instruments

TNETV1644ZDU6 数据表(HTML) 185 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载