AM186ED-20KCSLASHW datasheet(45/88 Pages) AMD

45 / 88 page

Am186ED/EDLV Microcontrollers

PRELI M INARY

F T

TIMER CONTROL UNIT

There are three 16-bit programmable timers and a

watchdog timer on the Am186ED/EDLV microcontrol-

lers.

Timer 0 and timer 1 are connected to four external pins

(each one has an input and an output). These two tim-

ers can be used to count or time external events, or to

generate nonrepetitive or variable-duty-cycle wave-

forms. When pulse width demodulation is enabled,

timer 0 and timer 1 are used to measure the width of

the High and Low pulses on the PWD pin. (See the

Pulse Width Demodulation section on page 45.)

Timer 2 is not connected to any external pins. It can be

used for real-time coding and time-delay applications.

It can also be used as a prescaler to timers 0 and 1 or

to synchronize DMA transfers.

The programmable timers are controlled by eleven 16-

bit registers in the peripheral control block. A timer’s

timer-count register contains the current value of that

timer. The timer-count register can be read or written

with a value at any time, whether the timer is running or

not. The microcontroller increments the value of the

timer-count register each time a timer event occurs.

Each timer also has a maximum-count register that de-

fines the maximum value the timer can reach. When

the timer reaches the maximum value, it resets to 0

during the same clock cycle. The value in the maxi-

mum-count register is never stored in the timer-count

mum-count register. Using both the primary and sec-

ondary maximum-count registers lets the timer

alternate between two maximum values.

If the timer is programmed to use only the primary max-

imum-count register, the timer output pin switches Low

for one clock cycle after the maximum value is

reached. If the timer is programmed to use both of its

maximum-count registers, the output pin indicates

which maximum-count register is currently in control,

thereby creating a waveform. The duty cycle of the

waveform depends on the values in the maximum-

count registers.

Each timer is serviced every fourth clock cycle, so a

timer can operate at a speed of up to one-quarter of the

internal clock frequency. A timer can be clocked exter-

nally at this same frequency; however, because of in-

ternal synchronization and pipelining of the timer

circuitry, the timer output can take up to six clock cycles

to respond to the clock or gate input.

Watchdog Timer

The Am186ED/EDLV microcontrollers provide a true

watchdog timer function. The Watchdog Timer (WDT)

can be used to regain control of the system when soft-

ware fails to respond as expected. The WDT is active

after reset. It can only be modified a single time by a

keyed sequence of writes to the watchdog timer control

can either disable the timer or modify the timeout pe-

riod and the action taken upon timeout. A keyed se-

quence is also required to reset the current WDT count.

This behavior ensures that randomly executing code

will not prevent a WDT event from occurring.

The WDT supports up to a 1.67-second timeout period

in a 40-MHz system. After reset, the WDT is enabled

and the timeout period is set to its maximum value.

The WDT can be configured to cause either an NMI in-

terrupt or a system reset upon timeout. If the WDT is

configured for NMI, the NMIFLAG in the WDTCON reg-

ister is set when the NMI is generated. The NMI inter-

rupt service routine (ISR) should examine this flag to

determine if the interrupt was generated by the WDT or

by an external source. If the NMIFLAG is set, the ISR

should clear the flag by writing the correct keyed se-

quence to the WDTCON register. If the NMIFLAG is set

when a second WDT timeout occurs, a WDT system

reset is generated rather than a second NMI event.

When the processor takes a WDT reset, either due to

a single WDT event with the WDT configured to gener-

ate resets or due to a WDT event with the NMIFLAG

set, the RSTFLAG in the WDTCON register is set. This

allows system initialization code to differentiate be-

tween a hardware reset and a WDT reset and take ap-

propriate action. The RSTFLAG is cleared when the

WDTCON register is read or written. The processor

does not resample external pins during a WDT reset.

This means that the clocking, the reset configuration

able during reset do not change when a WDT system

reset occurs. All other activities are identical to those of

a normal system reset.

Note: The Watchdog Timer (WDT) is active after re-

set.

PULSE WIDTH DEMODULATION

For many applications, such as bar-code reading, it is

necessary to measure the width of a signal in both its

High and Low phases. The Am186ED/EDLV microcon-

trollers provide a pulse-width demodulation (PWD) op-

tion to fulfill this need. The PWD bit in the System

Configuration Register (SYSCON) enables the PWD

option. Analog-to-digital conversion is not supported.

In PWD mode, TMRIN0, TMRIN1, INT2, and INT4 are

configured internal to the microcontroller to support the

detection of rising and falling edges on the PWD input

pin (INT2/INTA0/PWD) and to enable either timer 0

when the signal is High or timer 1 when the signal is

Low. The INT4, TMRIN0, and TMRIN1 pins are not

used in PWD mode and so are available for use as

PIOs.

AM186ED-20KC/W 数据表(PDF) 45 Page - Advanced Micro Devices

AM186ED-20KC/W 数据表(HTML) 45 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

数据表下载